Bedienungsanleitung JL Audio 3 (Seite 1 von 2) (Englisch)

700478

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Remote Turn-On

[FR–]

[FR+]

[SUB–]

[SUB+]

[FL–]

[FL+]

[SUB IN]

Source

[REM]

Battery

Fuse

(not included)

[+12V]

[GND]

[FRONT IN]

Thank you for purchasing a JL Audio amplifier for

your sound system.

Your amplifier has been designed and manufactured to exacting

standards in order to ensure years of musical enjoyment. For maximum

performance, we highly recommend that you have

your new amplifier installed by an authorized JL Audio dealer. Your

authorized dealer has the training, expertise and installation equipment

to ensure optimum performance from this product. Should you

decide to install the amplifier yourself, please take the time

to read this manual thoroughly to familiarize yourself

with its installation requirements and setup procedures.

If you have any questions regarding the instructions in this

manual or any aspect of your amplifier’s operation, please contact your

authorized JL Audio dealer for assistance. If you need further assistance,

please call the JL Audio Technical Support Department

at technical@jlaudio.com or call (954) 443–1100 during business hours.

OWNER’S MANUAL

600W 3-Channel Class D System Amplier

What’s Included

(1) Amplifier

(4) Stainless steel mounting screws

(1) User manual

Product Description

This is a three-channel, system amplifier utilizing Class D technology for all

channels.

Installation Applications

This amplifier is designed for operation with 12 volt, negative-ground electrical

systems. Using this product in systems with positive ground and/or voltages

other than 12V may result in damage to the product and will void the warranty.

This product is not certified or approved for use in aircraft.

Safety Considerations

• Whenever possible, mount the amplifier in a dry, well-ventilated location

that does not interfere with other factory installed electronic devices. If a dry

environment is not available, a location that is not exposed to heavy splashing

may be used.

• While this amplifier is designed to be water-resistant, it should never be

submerged under water or subjected to high-pressure water spray.

Do not install where it will be directly exposed to the elements.

• Do not mount the amplifier in the engine compartment or in any areas of

extreme heat.

• Securely mount the amplifier so that it does not come loose in the

event of a collision/sudden jolt or as a result of repeated vibrations during

normal operation.

• Check before drilling to make sure that you will not be drilling into an exterior

panel/hull, fuel tank, gas/brake line, wiring harness, or other vital system.

• Do not run system wiring outside or underneath the vehicle/vessel. This is an

extremely dangerous practice, which can result in severe damage/injury.

• Protect all system wires from sharp edges (metal, fiberglass, etc.) by

carefully routing them, tying them down and using grommets and loom

where appropriate.

• Secure all wiring as needed, using cable ties or wire clamps to protect them

from moving parts and sharp edges.

IPX7 Water Resistance Rating

This product has been tested to withstand immersion in water, up to 1 meter

(3.28 ft.) deep, for up to 30 minutes (with control panel cover properly installed).

Note - while designed to be water resistant, this product should never be

submerged under water for prolonged periods or subjected to activity that

creates pressure on it that exceeds its depth rating.

Installation Procedure/Connections

1. Disconnect the NEGATIVE battery post connection and secure the

disconnected cable to prevent accidental reconnection during installation.

This is an essential safety precaution during installation!

2. Connect the RED power lead to the positive (+12V) battery post. 4 AWG is

the minimum power wire size for this amplifier.

3. An appropriate fuse (sold separately), such as the JL Audio Water-Resistant

Master MAXI™ Fuse Block (XD-MFBW-MAXI), at the main power wire(s) to

the amplifier(s) is vital for vehicle/vessel safety. This fuse must be installed

within 18 inches (45 cm) of the positive battery post connection. If this is

the only device connected to this main wire, use a 60A fuse. Do not install

the fuse until the power wire has been securely connected to the amplifier.

4. Connect the BLACK negative ground lead to a clean, solid metal grounding

point near the amplifier. This can be to metal chassis ground, if available.

If no metal chassis ground is available, it may be necessary to make this

connection to the NEGATIVE battery post. 4 AWG is the minimum ground

wire size for this amplifier. All ground connections (source unit and

amplifiers) should be made at the same location.

5. Connect the BLUE remote turn-on lead to the source unit’s positive (+12V)

remote turn-on output. If your source unit does not have a dedicated

remote turn-on output, the amplifier’s turn-on lead can be connected to

+12V via a switch that derives power from an ignition-switched circuit.

6. Signal Input (Low-Level): Connect the amplifier’s RCA input jacks to the

source unit’s preamp level output jacks.

7. Signal Input (High-Level): If your source unit does not offer preamp level

signal outputs, you can splice the speaker output wires of the source unit

onto a pair of RCA plugs for each input pair or use the JL Audio ECS Speaker

Wire to RCA adaptor (XD-CLRAIC2-SW). Make sure to observe correct

polarity in making “High-Level Input” connections. Failure to do so will result

in a loss of signal (poor performance).

8. Connect the speaker output leads to the corresponding speaker wires.

9. Make necessary adjustments to the filter controls and input sensitivity.

10. The amplifier’s subwoofer output level can be controlled from the front

of the vehicle/vessel with an optional remote level controller (sold

separately). Use the RBC-1 for standard (dry) installations or the M-RBC-1

for applications exposed to moisture. Connect the remote’s plug to the

amplifier’s harness-mounted RJ11 input jack. (Refer to Appendix B)

WARNING! Failure to make safe, tight, high-integrity power connections

can result in fire and extensive damage!

Control Setting Mode / Function

Front / Subwoofer

Input

Voltage

Low RCA/Preamp Level Range (250 mV - 4 V)

High RCA/Preamp or Speaker Level Range (580 mV - 14 V)

Input

Sens.

Variable

Adjusts the input stage of each pair of amplifier channels to

match the source unit’s output voltage for maximum clean

output (refer to Appendix A)

Front

Input

Mode

2CH

Applies two channels of input to all three

amplifier channels. Main input signals will be

combined to mono for the subwoofer channel.

Use Front

Inputs Only

4CH

Sends four discrete channels to all four inputs.

L & R Sub Inputs will be combined to mono.

If only one channel of subwoofer signal is

available, we recommend using a Y-adaptor to

feed both Sub Inputs.

Use Front

and Sub

Inputs

Filter

Freq. (Hz)

Variable

Adjusts the high-pass filter cutoff frequency, variable from

35-300 Hz, 12 dB/Octave

Subwoofer

Output

Polarity

0 Normal speaker polarity

180 deg. Polarity reversed 180 degrees

Infrasonic

Filter (Hz)

Variable

Adjusts the high-pass filter cutoff frequency, variable from

20-40 Hz, 12 dB/Octave

LP Filter

Freq. (Hz)

Variable

Adjusts the low-pass filter cutoff frequency, variable from

40-400 Hz, 24 dB/Octave

Bass

Boost (dB)

Variable

Boost-Only Bass Equalizer: Boost range from 0dB (full-

counterclockwise) to + 12dB (full-clockwise), centered

at 43 Hz.

Control Panel Settings and Adjustments

The amplifier’s settings and controls are located on the bottom panel beneath a

gasketed, protective cover. Remove the four Phillips head screws from the center

panel to access the controls and make adjustments. Replace cover when finished

and mount the amplifier.

Power Connections

Label Wire Color Description

+12V Red Positive (+12V) Power Connection

GND Black Negative (GND) Ground Connection

REM Blue Positive (+12V) Remote Turn-On Input

Inputs

Label Plug Description

FRONT

White RCA Ch. 1 / Front Left Channel Signal Input

Red RCA Ch. 2 / Front Right Channel Signal Input

SUB

White RCA

Ch. 3 / Left Subwoofer

Channel Signal Input

Note: L & R Sub Inputs will be

combined to mono. If only one

channel of subwoofer signal is

available, we recommend using a

Y-adaptor to feed both Sub Inputs.

Red RCA

Ch. 4 / Right Subwoofer

Channel Signal Input

Outputs

Label Wire Color Description

FL+ White

Ch. 1

(+) Positive Front Left Speaker Front Bridged (+)

FL– White/Black (–) Negative Front Left Speaker

FR+ Gray

Ch. 2

(+) Positive Front Right Speaker

FR– Gray/Black (–) Negative Front Right Speaker Front Bridged (–)

SUB+ Lt. Blue

Ch. 3

(+) Positive Subwoofer Output

SUB– Lt. Blue/Black (–) Negative Subwoofer Output

Optional

Remote Bass

Control Jack

RJ11 Input Jack for M-RBC-1 or RBC-1 (each sold separately)

Connections

IPX7

WATER

RESISTANT

Power

Connections

Wiring Diagram

Outputs:

To Speakers

Inputs:

High-Level

< or >

Low-Level

(selectable via

Input Voltage

switch for each

channel pair)

Optional:

M-RBC-1

Remote

Bass Control

(sold separately)

JL Audio 3 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info