Bedienungsanleitung JL Audio 3v2 (Seite 14 von 20) (Englisch)

700458

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

14 | JL Audio - XD500/3v2 Owner’s Manual

APPENDIX A:

Input Sensitivity Level Setting

Following the directions below will allow the

installer to adjust the input sensitivity of each

amplifier channel pair simply and easily in just a

few minutes using equipment which is commonly

available in installation bays.

Necessary Equipment

• Digital AC Voltmeter

• CD with a sine-wave test tone recorded at

0 dB reference level in the frequency range

to be amplified for that set of channels

(50 Hz for subwoofer channels, 1 kHz for a

midrange application). Do not use attenuated

test tones (-10 dB, -20 dB, etc.).

The Nine-Step Procedure

1) Disconnect the speaker(s) from the

amplifier’s speaker output connectors.

2) Turn off all processing (bass/treble, loudness,

EQ, etc.) on the source unit, processors (if

used) and amplifier. Set the fader control to

center position and the subwoofer level control

to 3/4 of maximum (if used to feed

the XD500/3v2).

3) Switch the “Input Voltage” switch to “Low”

and turn all three “Input Sens.” controls all

the way down.

4) Set the source unit volume to 3/4 of full

volume. This will allow for reasonable gain

overlap with moderate clipping at full volume.

5) Using the chart on this page, determine

the target voltage for input sensitivity

adjustment according to the nominal

impedance of the speaker system

connected to the amplifier outputs.

6) Verify that you have disconnected the speakers

before proceeding. Play a track with an

appropriate sine wave (within the frequency

range to be amplified by the XD500/3v2) at 3/4

source unit volume.

7) Connect the AC voltmeter to the speaker

output connectors of the amplifier. Make sure

you test the voltage at the correct connectors

(+ and –).

8) Increase the “Input Sens.” control until the

target voltage is observed with the voltmeter.

9) Once you have adjusted each channel

section on the XD500/3v2 to its maximum

low-distortion output level, reconnect the

speaker(s). The “Input Sens.” controls can

now be adjusted downward if the amplifier

requires attenuation to achieve the desired

system balance.

Do not increase any “Input Sens.” setting for

any amplifier channel or channel pair in the

system beyond the maximum level established

during this procedure. Doing so will result in

audible distortion and possible speaker damage.

It will be necessary to readjust the

“Input Sens.” for the affected channels if any

equalizer boost is activated after setting the

“Input Sens.” with this procedure. This applies

to any EQ boost circuit, including source unit

tone controls or EQ circuits. EQ cuts will not

require re-adjustment.

Nom.

Impedance

Target AC Voltage

CH 1 & 2

(Stereo)

CH 1 & 2

(Bridged)

Subwoofer CH

8

17.3 V 34.6 V 26.8 V

4

17.3 V 28.2 V 26.8 V

3

16.2 V not recommended 26.8 V

2

14.1 V not recommended 24.5 V

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JL Audio 3v2 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info