Bedienungsanleitung JL Audio HD900 (Seite 3 von 13) (Englisch)

700440

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

4 | JL Audio - HD900/5 Owner’s Manual

TYPICAL INSTALLATION SEQUENCE

The following represents the sequence for

a typical amplifier installation, using an

aftermarket source unit or OEM Interface

processor (like the CleanSweep® CL441dsp).

Additional steps and different procedures may

be required in some applications. If you have

any questions, please contact your authorized

JL Audio dealer for assistance.

1) Disconnect the negative battery post

connection and secure the disconnected cable

to prevent accidental re-connection during

installation. This step is not optional!

2) Run power wire from the battery location

to the amplifier mounting location, taking

care to route it in such a way that it will

not be damaged and will not interfere with

vehicle operation. 4 AWG is the minimum

recommended wire size for this amplifier.

Use a 2 AWG or 1/0 AWG main power

wire with a fused power distribution

block when additional amplifiers are

being installed with the HD900/5 and

powered from the same main power wire.

3) Connect power wire to the positive battery

post. Fuse the wire with an appropriate fuse

block (and connectors) within 18 inches (45

cm) wire length of the positive battery post.

This fuse is essential to protect the vehicle.

Do not install the fuse until the power wire

has been connected to the amplifier.

4) Run signal cables (RCA cables) and remote

turn-on wire from the source unit or interface

processor to the amplifier mounting location.

5) Run speaker wire from the speaker systems to

the amplifier mounting location.

6) Find a good, solid, bare metal grounding

point close to the amplifier and connect the

negative power wire to it using appropriate

hardware. Use minimum 4 AWG wire up to

60 inches (150 cm) long from the amplifier

to the ground connection point. In some

vehicles, it may be necessary to upgrade the

battery’s ground wire as well. (See page 7 for

important notice).

7) Securely mount the amplifier using

appropriate hardware. (See page 8 for detailed

mounting instructions).

8) Connect the remote turn-on wire and the

positive and negative power wires to the

amplifier’s power connector plug. Then insert

the power connector plug into the amplifier’s

power connector receptacle, pushing firmly.

9) Connect the RCA input cables

to the amplifier.

10) Connect the speaker wires to the speaker

connector plugs and insert the plugs firmly

into the speaker connector receptacles.

11) Carefully review the amplifier’s control

settings to make sure that they are set

according to the needs of the system.

12) Install power wire fuse (60A for a

single HD900/5) and reconnect the negative

battery post terminal.

13) Turn on the source unit at a low level

to double-check that the amplifier is

configured correctly. Resist the temptation

to crank it up until you have verified the

control settings.

14) Make necessary adjustments to the input

sensitivity controls to obtain the right

overall output and the desired balance

in the system. See Appendix C (pages 18, 19)

for the recommended input sensitivity

setting method.

15) Enjoy the fruits of your labor with your

favorite music.

PRODUCT DESCRIPTION

The JL Audio HD900/5 is a very powerful

and compact five-channel amplifier utilizing

patented Single Cycle Control™ Class D

technology for all channels. This groundbreaking

technology delivers reference-grade, full-

range sonic performance while requiring

far less current from the vehicle’s electrical

system than a conventional amplifier.

JL Audio’s exclusive R.I.P.S. power supply

design optimizes the output of each channel

section for any impedance between 1.5 and 4

ohms per channel (3-8 ohms bridged on front and

rear sections) allowing you to get full use of the

HD900/5’s performance capabilities with a wide

range of speaker systems.

The tightly regulated power supply design also

means that the HD900/5’s clean power output

capability remains stable over a wide range of

vehicle voltages, resulting in enhanced fidelity.

The HD900/5 flexible, studio-grade signal

processing allows it to be deployed in several

different system configurations:

1) As a five-channel amplifier in a bi-amplified

system, driving four satellite speakers (100W x

4), plus a subwoofer system (500W x 1).

2) As a very powerful three-channel amplifier

in a bi-amplified system, driving two satellite

speakers (150W x 2, bridged), plus a subwoofer

system (500W x 1).

3) As a five-channel amplifier in a tri-amplified

system, driving two tweeters (100W x 2), plus

two woofer/mids (100W x 2), plus a subwoofer

system (500W x 1). An external 2-way

crossover is required for this application.

The HD900/5’s flexible input and crossover

sections permit operation with a wide variety

of source units and system configurations.

It can be operated with a single pair of

stereo inputs, with two pairs of stereo inputs

(front and rear) or with separate inputs for

its front, rear and subwoofer channels.

As we said, it’s very flexible.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JL Audio HD900 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info