Bedienungsanleitung JL Audio M700 (Seite 10 von 20) (Englisch)

700493

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

10 | JL Audio - M700/5 Owner’s Manual

When a pair of the M700/5’s main channels

are bridged, they will deliver 200W x 1 into a

4 ohm load or 150W x 1 into an 8 ohm load.

Operating a pair of bridged channels into a

load lower than 4 ohms is not recommended.

A bridged pair of channels requires that both

channels in the pair receive input. You must

connect the mono or stereo source signal to

both the left and right inputs the bridged

channel pair. Connection of only one input will

result in reduced power output, increased

distortion and can cause the amplifier to

overheat. Do not do this!

When a pair of the M700/5’s main channels

are operating in bridged mode, the output will be

in mono (only one channel). This mono channel

can contain only right channel information, only

left channel information, or the sum of the signals

from right and left input channels. In order to

achieve one of these options, configure the inputs

to that pair of channels in one of these two ways:

1) Left Channel Only or Right Channel Only

Information: If you wish to send a left-only

or right-only signal to a pair of the M700/5’s

channels you must use a “Y-Adaptor” to split

the single channel signal into both left and

right RCA inputs of the bridged channel

pair. This option is used when deploying a pair

of the M700/5’s main channels to drive left

channel speakers only and the other pair of the

M700/5’s main channels to drive right channel

speakers only.

2) Left + Right Channel Information: When

bridged and fed by a stereo source signal, a

bridged pair of the M700/5’s channels will

automatically combine the left and right input

signals into a summed mono (left + right)

input signal.

SUBWOOFER OUTPUTS

The M700/5’s single subwoofer channel is

designed to deliver power into subwoofer loads

equal to or greater than 2 ohms. It is rated for

300W into 2 ohms, 250W into 3 ohms and 200W

into 4 ohms (Continuous Power, RMS Method).

Subwoofer loads below 2 ohms nominal are not

recommended and may cause the amplifier

to initiate a protection mode which reduces

power output.

The M700/5’s subwoofer outputs are designed

to accept 16 AWG - 8 AWG wire. To connect

the subwoofer wires to the amplifier, first back

out the set screws on the top of the terminal

block, using the supplied 2.5 mm hex wrench.

Strip 1/2 inch (12 mm) of insulation from the

end of each wire and insert the bare wire into

the terminal block, seating it firmly so that no

bare wire is exposed. While holding the wire

in place, tighten the set screw firmly, taking

care not to strip the head of the screw.

You will notice that there are two “+” positive

connections and two “–” negative connections.

This is to facilitate multiple subwoofer wiring.

The two positive and two negative connections

are connected in parallel inside the amplifier

They are not stereo outputs. Connecting two

subwoofers, each to one set of positive and

negative terminals, will result in a parallel

subwoofer connection. If only connecting one

pair of subwoofer wires, it is not necessary to use

both sets of connections.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JL Audio M700 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info