Bedienungsanleitung JL Audio MHD900 (Seite 13 von 24) (Englisch)

700488

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

REMOTE LEVEL CONTROL OPTIONAL

With the addition of the optional Remote

Level Control (HD-RLC), you can control

the level of the Subwoofer Channel of the

MDH900/5-24V from the front of the vessel. The

HD-RLC connects to the jack labeled “Remote

Level Control” on the Connection Panel of

the amplifier using a standard telephone cable

(supplied with the HD-RLC).

If desired, multiple MHD amplifiers can be

controlled from a single HD-RLC controller

using a simple phone line “splitter”

and multiple phone cables.

When connected to the amplifier, the HD-RLC

operates as follows. At full counter-clockwise

rotation, the audio will mute completely. At full

clockwise rotation the level will be the same as if

the HD-RLC was not connected at all. In other

words, it operates strictly as a level attenuator.

When no HD-RLC is connected, the Level

Control circuit is defeated.

The RBC-1 Remote Bass Control used with

JL Audio Slash, Slash v2, e-Series, A-Series and

G-Series amplifiers is NOT compatible with the

HD/MHD Series amplifiers. If you attempt to

connect an RBC-1 to an HD amplifer, the

control will not work. You must use the

HD-RLC controller.

SPEAKER OUTPUTS

The MDH900/5-24V employs JL Audio’s

exclusive Regulated, Intelligent Power Supply

(R.I.P.S.) design. The operation of the R.I.P.S.

system is independent for each channel section.

This sophisticated power supply allows the

amplifier to produce its optimum power into

higher impedances as well as low impedances.

The R.I.P.S.-equipped MDH900/5-24V gives

you the freedom to use a variety of speaker

configurations that achieve final nominal

impedances between 1.5 – 4Ω per channel

in stereo while maintaining 75 - 100W x 4

of clean power output. When bridged, each

main channel pair will optimize output at

150-200 watts between 3 – 8Ω. The mono

subwoofer channel will deliver its full 500W

output into any impedance between 1.5-4Ω.

The operation of the R.I.P.S. circuitry is

entirely automatic and adjusts itself every time the

amplifier is turned on. There are no user controls

to configure. The system operates through

multiple stages of impedance optimization,

choosing the stage most appropriate to the actual

impedance of the speakers you connect to it.

If you connect a load higher than 4Ω nominal

per channel in stereo mode (or 8Ω in bridged

mode), power will drop by half with every

doubling of impedance above 4Ω stereo / 8Ω

mono. If you connect a load lower than 1.5Ω

nominal per channel in stereo mode (or 3Ω in

bridged mode, the amplifier protection

circuitry activates a “safe” mode which reduces

amplifier power to protect the circuitry from

failure (the LED status indicator on the control

panel will light up amber to indicate that this

has happened). See page 15 for details.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JL Audio MHD900 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JL Audio MHD900

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info