Bedienungsanleitung JL Audio ZR570-CSi (Seite 4 von 12) (Englisch)

701370

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

4 JL AUDIO ZR570-CSi

GETTING STARTED:

• Turn off the audio system. It is also advisable

to disconnect the negative (–) terminal of your

vehicle’s battery whenever performing

installation work.

• Before cutting, drilling or inserting any screw, check

clearances on both sides of the planned mounting

surface. Also check for any potential obstacles, such

as window tracks and motors, wiring harnesses, etc.

Check both sides of the vehicle, many vehicles are

not symmetrical!

• Always wear protective eyewear.

CROSSOVER NETWORK INSTALLATION:

The crossover networks supplied with your ZR

System should be installed in a dry location inside

your vehicle. DO NOT INSTALL THEM INSIDE OF

A DOOR! Doors often get wet on the inside, which

can damage your crossover networks and could

potentially damage your entire sound system. The

crossovers can be screwed into a solid surface via

two holes located under the protective cover of the

case. To access these holes, simply squeeze the sides

of the cover while gently pulling the cover away from

the base. Make sure that your mounting location will

not cause damage to wiring, fuel lines, brake lines or

any other vital component of your vehicle. Once you

have screwed the case in and made your connections,

snap the protective cover back into place.

WARNING

It is absolutely vital that your component system is

connected as shown in this manual. Failure to connect

the system as shown may result in damage to your

speakers which is NOT covered under warranty.

Do not substitute different crossover networks into

your ZR System. Do not use crossover networks

intended for different ZR models.

WIRING DIAGRAMS - STANDARD AND

BI-AMP / BI-WIRE METHODS:

The input to the crossover networks can be set

up in one of the following two ways:

Standard: This wiring configuration is used when

you wish to drive each crossover with a single

amplifier channel or pair of wires. In this mode, you

will only use the input connections marked “INL+”

and “INL–”on the crossover circuit board (“INH+”

and “INH–” are not used). Your crossovers are pre-

set in this mode at the factory. This mode is selected

by placing the pair of jumper bars shown in Diagram

A to the lower position marked "STD”. Tweeter

(“T+” and “T–”) and woofer output connections

(“W+” and “W–”)are made as shown in Diagram A.

Bi-Wire (Bi-Amp): This position is selected by

placing the input mode selection jumper bars in the

upper position as shown in Diagram B. In this mode,

the inputs to the woofer’s low-pass filter and the

tweeter’s high-pass filter are electrically isolated. This

permits connection of different amplifier channels to

the woofer and tweeter sections (bi-amp), or separate

wire pairs for each section from a single amplifier

channel (bi-wire). In this mode, you will use the Input

connections marked “INL+” and “INL–” to drive the

low-pass woofer section of the crossover and “INH+”

and “INH–” to drive the high-pass tweeter section of

the crossover. Tweeter (“T+” and “T–”) and woofer

output connections (“W+” and “W–”)are made as

shown in Diagram B.

Please note that the use of additional active

filtering for the woofer low-pass or tweeter high-

pass is not necessary or recommended in this

mode. The crossover network has been engineered

to shape the system response... additional filters

may degrade performance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JL Audio ZR570-CSi Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info