Bedienungsanleitung Jocca 6642 (Seite 13 von 30) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

553865

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

4.- Insert the thread through the small bobbin hole from the

inside and take out about 8 cm of thread.

5.- Hold the end of the thread tight and press the ON button or

the control pedal. Stop once it has gone around a few times.

6.- Cut the end of the thread with scissors in the top part of the

bobbin and then continue with the winding until the amount of

thread desired is wound.

7.- Cut the thread at about 8 cm from the bobbin. Extract the

thread bobbin from the spindle.

8.- Put away the spindle rewinder and put the long spindle in its

place.

NEEDLE CHANGE

1.- Lift up the needle to its maximum position by turning the

balance wheel with the presser foot in its lowest position.

2.- Hold it and release the screw that adjusts the needle. Remove

the needle.

3.- Put the new needle in the support with the flat part to the

side of the machine making sure that the needle eye is facing

the front of the machine. Do not try to push the needle upwards

whilst placing it in the support before adjusting the screw.

4.- Tight the needle adjustment screw.

CLEANING AND STORAGE

-For correct operation, the machine requires regular cleaning

and greasing.

IMPORTANT: Before cleaning, make sure the machine is

disconnected from the mains and that it does not have any

batteries inside.

-Use a cloth to clean the machine and remove any surplus oil.

-Do not use lubricants such as solvents, abrasive detergents or

products that may damage the machine.

-Use specific oil for sewing machines (any other type of oil could

damage it). Oil with one drop where there is friction.

-NEVER SUBMERGE THE MACHINE IN WATER OR IN ANY

OTHER LIQUID.

FREQUENT PROBLEMS

1. The top thread is not properly threaded.

2. The control pedal is not connected to its corresponding socket.

3. The needle is not correctly placed in its support.

4. The needle eye is not facing the front part of the machine.

5. The needle is bent.

6. The lower thread is not properly threaded or is broken.

7. An incorrect sized lower bobbin is being used.

8. The thread tension is not correct.

9. The lower bobbin and its support are not in the correct position,

so the support is blocked and does not turn clockwise.

TECHNICAL SPECIFICATIONS

6V DC (4xAA 1,5V)

This appliance conforms to the safety requirements and

provisions of directives 2006/95/EC on Low tension devices and

2004/108EC on Electromagnetic Compatibility.

PROTECTION OF THE ENVIROMENT – DIRECTIVE

2002/96/EC

This product has been designed and manufactured with high

quality materials and components that can be recycled and

reused.

When you see the symbol of a crossed out litter bin on

wheels next to a product, this means that the product

conforms to the European Directive 2002/96/EC.

Please obtain information about the local recycling system

for electric and electronic products.

Follow the local rules and do not dispose of used products by

throwing them in the normal bins at home. Proper recycling

of your used product will help avoid negative impacts on the

environment and people’s health.

EN-25

24-EN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jocca 6642 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info