Bedienungsanleitung Joie iBase - Gemm (Seite 7 von 68) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch)

768450

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

11 12

Concerns on Installation

! DO NOT install this infant child restraint on vehicle seats with Lap

Belts.(Fig. 1)

! This infant child restraint is suitable for vehicle seats with a 3-point

Retractor Safety Belt (with or without base) ONLY (Fig. 2), and

ISOFIX anchor points WITH the Base. (Fig. 3)

! DO NOT install this infant child restraint on vehicle seats that face

sideways or rearward with respect to the moving direction of the

vehicle. (Fig. 4.1)

! DO NOT place rear-facing infant child restraint on frontal seat with

air bag (Fig. 4.2), death or serious injury may occur. Please

reference vehicle owner’s manual for more information.

! It is recommended to install this infant child restraint on the rear

vehicle seat. (Fig. 4.3)

! DO NOT install this infant child restraint on vehicle seats movable

during installation.

! To know more detailed installation information for seat with base,

please refer to the section 'Vehicle Fitting Information'.

Installing with Base

a. Installation with 3-point-belt

1. Unfold the load leg from storage compartment. (Fig. 5)

2. After placing the base on the vehicle seat, extend the load leg to

floor (Fig. 6), the load leg indicator shows green means it is installed

correctly, red means it is installed incorrectly. (Fig. 6.3)

! The load leg has 24 positions. When the load leg indicator

shows red this means the load leg is in the wrong position.

! Make sure the load leg is secure by pressing down on the front

of the base.

! Squeeze the load leg releasing button, then shorten the load leg

upwards.

3. Open the lock-off and route the vehicle safety belt through the

belt path (Fig. 7.1), and lock it into the buckle. (Fig. 7.2)

4. Tighten the vehicle safety belt as much as possible while pushing

down on the base, and check it is not loose or twisted, then close

the lock-off. (Fig. 7.3)

! The infant child restraint can not be used if the vehicle safety

belt with female buckle is too long to tie the base. (Fig. 7.4)

! Check that the safety belt does not move by pulling and pushing

hard on base. If belt loosens or lengthens, repeat procedure.

The installed base is shown as Fig. 8

! Please ensure that there is no gap between the vehicle seat and the

bottom of the base.

! The safety belt must go under the lock-off, not over the lock-off.

(Fig. 8.1)

! The safety belt must be locked into the buckle. (Fig. 8.2)

! The load leg must be installed correctly with green indicator.

(Fig. 8.3)

5. Push the infant carrier module down into the base (Fig. 9), if the

infant child restraint is secure, the infant child restraint indicator

shows green. If the infant child restraint is not secure, the indicator

shows red. (Fig. 10)

! Pull up on the infant carrier module to be sure it is securely

latched into the base.

6. To release the infant carrier module, pull the infant carrier module up

while squeezing the infant carrier module release button. (Fig. 11)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Joie iBase - Gemm Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info