•It is NOT allowed to connect more than one motor to the same single switch. The centralisation controls can be done by an appropriate devices,
which are supplied on request.
•The gear motor is made for intermittent working. However, it is provided by an internal thermal protection, which stops the power supply in case of
overheating, for example after continuous operations (more than 10 non-stop). The motor re-functioning happens after a time not lower than 10
minutes, at the end of which the thermal protection resets itself automatically. But, after this resetting, the motor can function at a reduced rate; the
normal functioning will be possible only after a complete motor cooling (about 60 minutes).
•If the electricity supply cable of this motor is damaged, it must be replaced only by a repair centre, recognised by the manufacturer, as it is necessary
to use special equipment. In cases where such indications are not adhered to, the guarantee will be rendered invalid..
4 Limit switch adjustment
WARNING
:
•In order to avoid injury or damage to the device during the regulation procedure of the
stop, it is essential to be able to stop the coiler tube at any moment.
•It is recommended that you use a normal screwdriver to regulate the route end points.
If you use and electric screwdriver use a very low rotation velocity (inferior to 100
RPM) without exerting pressure on the screws.
•In the case of rolling shutters, do not install stopper or stop carriers on the end blade.
LIMIT SWITCH ADJUSTMENT:
a)Lower the tube, without the roller, until the motor stops automatically.
b)While keeping the down button pressed, turn the lower end run adjustment screw (see
figure) anti-clockwise (+), until the roller tube is in a suitable position for anchoring the
roller shutter.
c)Fix the roller shutter to the tube. Warning: DO NOT USE over-long screws.
d)Raise the roller shutter/awning until the motor stops automatically.
e)While keeping the up button pressed, turn the upper end run adjustment screw (see
figure) anti-clockwise (+), until the roller shutter/awning reaches the topmost position
desired.
LATER ADJUSTMENTS:
If, for example, the upper stopping point has been set too high, move the roller shutter or
awning to a position below the desired stopping point. At this point, turn the upper end run
adjustment screw a few times in a clockwise direction (−), and then start the procedure
again from point d).
NOTE
: for awnings we advise you to:
•Regulate the stop points with a reasonable safety margin that takes into account the size variations of the tent sheet due to various phenomenon such as heat and humidity… .
•One first check is suggested after few days from the installation and eventually a further end run adjustment to recover an eventual cloth “plays”.
•Use automatic closing systems in case of strong wind in order to avoid damage to the motor.
5 Reducer gearboxes with supplementary operation
Before utilizing the manual override switch off electric current of the motor.
The figure shows various installation possibilities of the manual maneuver with respect to the
position of the motor.
WARNING
:
•If the gear motor is provided by a manual override device,
it is necessary to take care to the motor orthogonality as
regards its fixing plan (static part).
•Only for reducer gearboxes with supplementary operation,
fit the stop brackets as to pic. 5, to avoid during manual
operation, the roller blind entering the housing completely.
In this case, adjust the limit switch so that the stop
brackets remain at least 5 cm lower than the stop
threshold.
6 Trouble shooting
1.THE MOTOR DOES NOT WORK:
•Check the electrical supply.
•Verify the correct execution of the electrical connections (see par. 3).
•If the problem occurs after numerous close operations the thermal protection could have intervened. In that case wait for the cooling of the system.
2.THE SHUTTER/SHADE DOES NOT STOP IN CORRESPONDENCE TO THE STOP:
•Check that the stop has been well inserted in the coiler tube (see point d) par. 2).
•Verify that the procedure for the regulation of the stops has been executed correctly (see par. 4).
•Check that the moving pulley is adequate and correctly inserted in the coiler tube.
•Verify the fastening of the pin square support to the roller-shutter box or to the wall.
3.THE MOTOR TURNS BUT THE ROLLER-SHUTTER/SHADE DOES NOT MOVE:
•Check that the roller-shutter/shade is fixed well to the coiler tube.
•Check that the moving pulley is correctly inserted in the shaft of the motor (see point b) par. 2).
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Jolly Motor FCI wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
