Dear customer, please read following instructions carefully, which guarantee the correct functioning of the motor and safety of people.
•
Do not ever allow people with reduced physical capacity or children to operate or play with switches or other control devices..
•
Check the rolling shutter while it moves and make sure that nobody gets close by until it is completely closed.
•
Check regularly the correct functioning of the installation.
•
In case of rolling shutters/awnings supervised by automatic systems, make sure that the motor cannot be started when works are carried out nearby (for example, when
windows are cleaned, we suggest to disconnect electricity supply by switching off the main.
•
The connection of the power supply cable is a “Y” type one. If the power cable of the motor is damaged, it must be replaced either by the manufacturer or its after seals
assistance or by a specifically qualified persons in order to avoid any hazard as specific tools are required for such purpose. Otherwise any guarantee will be declined.
•
If the motor is installed with the cable outdoor a special cable must be used . Otherwise it will be necessary to protect the standard P.V.C. cable (supplied with the motor),
by fitting it in specific tubes (conduits or anti UV protective coverings) for protection against atmospheric agents and sun rays.
•
Additional components for the implementation of the installation, such as adaptors and brackets must be chosen among those offered by the producer “Jolly Motor” through
its sales network. These products are listed in the catalogue supplied on request.
WARNING: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE. CAREFULLY FOLLOW ALL THE INSTALLATION INSTRUCTIONS
y
Before installing the geared motor remove all the unnecessary cables and disconnect any equipment not required for motorized operation.
y
If operations are controlled by a manual switch, this must be installed in view of the equipment, but far from the moving parts and at a height of at least 1.5 m.
y
If a manual release is provided, the actuating member is to be installed at a height less than 1.8 m.
y
When installing the awnings leave a space of at least 40 cm between the awning and any other objects.
y
The moving motor parts installed at less than 2.5 m from the floor must be suitably guarded.
y
Do not turn the control end run ring (1) before the installation of the gear motor and never strike the exit pins.
y
Do not drill the tube when the gear motor is switched on. The fixing of the mobile element will be done using screws with a length, which can guarantee that the jutting part
inside the tube will be 1 mm max, in order to avoid mechanical interference between the fixing and the rotating parts.
y
If the motor is installed in a rolling shutter box it must have a service opening based on DIN standard for adjusting and checking the system.
y
Our reducing gears are exclusively designed and sized for moving various types of rolling shutters for private homes or use with awnings. Any other use of the reducing
gears must be discussed ahead of time with the manufacturer for approval.
y
Our motors are correctly dimensioned and operations are compatible with the characteristics of the operated parts, only if the operating loads specified are complied with:
“Application diagram for rolling shutters”, “Application diagram for sun awnings”. Apply the motor respecting data written on its label.
y
Disconnect the supply current when you work near driving devices for awnings or shutters control, as an example when windows are washed.
2 Installation procedure
3 Electric connections
THE MEANING OF THE COLOUR OF THE WIRES IS THE FOLLOWING:
•YELLOW / GREEN cable: ground connection.
•BLACK cable: phase of the electrical supply for rotation in one direction.
•BROWN cable: phase of the electrical supply for rotation in the opposite direction.
•BLUE (GREY) cable: neutral of the electrical supply (common for both directions).
Once all electrical wiring connections have been completed, check that the rotation direction of the roller tube
corresponds to the direction shown on the buttons. If this is not the case, swap the black wire with the brown
wire.
WARNING
:
•The connection to the supply line (in the switchboard) must be made by a two-pole switch with an
opening distance of 3mm between contacts.
•The ‘balancing’ phase between the brown and the black cable is controlled by a switch with central zero
at permanent contact or automatic return. However, for application on awnings, the use of an automatic
return switch is suggested.
11
10
14
13
15
6
9
8
S-60
3
4
2
6
7
S-40 S-50
5
1
a)
If necessary, fix the square pin (3) to the end run block (3) using the screw (4).
b)Insert
the adapter ring (5) and the pulley (6) and fix the latter with the cotter (7) (series 40 and 50) or
by using the screw (8) and washer (9) (series 60).
c)Insert the cover (10) into the tube (11).
d)Insert the motor (12) into the roller tube (11) completely, WITHOUT HITING the square pin (2).
e)Hang the tube to its special fixed supports (13) and (14).
DO NOT FORCE while hanging it on the
motor side and place the tube so that the adjustment screws (15) can be reached easily.
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Jolly Motor FMMT wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
