Bedienungsanleitung Joovy 003 (Seite 3 von 12) (Englisch, Französisch, Spanisch)

780425

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

EN FR ES

• Bringtheseatbeltaroundthedoll’swaistandinsertthemaleendofeachwaiststrapbuckleintothefemalebuckle.Insurethattheysnap

into place. See Figure 5.3.Tightenthewaistbelttobesnugaroundthedoll’swaist.

• Buckle the harness clip pieces together. See Figure 5.4.PositiontheharnessclipIthemiddleofthedollorstuffedtoy’schest,levelwith

the armpits and away from the neck.

• Both the shoulder straps and the waist straps may be adjusted using the sliding buckle on these straps, located under the bottom of the

carrier. See Figure 5.5.

6 Using your Doll Car Seat in the Carrier Mode

• To use the product in carrier mode, position the handle in the UP position as described previously.

• The carrier may then be transported by holding on to the center of the handle and carrying it wherever your child goes.

!WARNING

NEVER use this toy to carry a baby or child for any purpose whatsoever.

DO NOT use as a carrier for any dolls or stuffed toys that weigh more than 4 lbs.

As with a real carrier, this toy carrier should never be placed near the edges of counter tops, tables, or other

elevated surfaces.

Using your Doll Car Seat in the Vehicle

7 Vehicle Seat Requirements

• The doll car seat should be placed in the center position of the seat directly behind the front seat whenever possible.

• Because a real car seat would not be placed in a vehicle location that has a front airbag, do not place this doll car seat in a similar

location.

• The vehicle seat should always be a forward facing seat and the seat should lock in an upright position.

8 Installing the Doll Carrier and Base Using Vehicle Belts

To install the toy car seat in a vehicle, you must carefully follow the instructions provided by your vehicle manufacturer in addition to the

information in this manual. Before proceeding, be sure you have read and understand all of the instructions in this section.

• Remove doll carrier from base. Place the base in a rear-facing position in the vehicle seat.

• Thread the vehicle seat belt inside and through the curved plastic piece under the base. See Figure 8.1.

• Buckle the vehicle seat belt, making sure the buckle tongue goes into the correct buckle. The vehicle belt should not be twisted. See

Figure 8.2.

• Secure the base tightly into position by pushing down on the middle of the base with one knee or free hand while tightening the vehicle

belt.Refertoyourvehicleowner’smanualforinstructionstoproperlytightenthevehiclebelt.

• Place the doll carrier in the base and make sure it “Clicks.” Pull up on the doll carrier to be sure it is latched securely in the base.

!WARNING

NEVER use this toy to hold a baby or child in a vehicle. Death or serious injury may occur.

DO NOT use as a car seat for any dolls or stuffed toys that weigh more than 4 lbs.

NEVER leave the car seat unsecured in a vehicle. An unsecured car seat can be thrown around and may injure you

or your child in a sharp turn, sudden stop, or crash.

DO NOT use this product if the carrier does not securely latch into the base. Contact Joovy Customer Service for

assistance.

9 Acceptable Vehicle Belt Systems

Thefollowingbeltsystemsareacceptableforusewithyourcarseat.Youshouldrefertoyourvehicleowner’smanualtodeterminewhich

type of seat belts your vehicle has.

• Lap Belts-Manually Adjusted: When buckled, the belt is tightened manually by pulling on the excess belt while pushing down hard on the

car seat base.

• Lap Belts with Automatic Locking Retractor (ALR): The automatic locking retractor will not allow the lap belt to lengthen once it is buckled.

Tighten the belt by feeding the belt back into the retractor while pushing down hard on the car seat base.

• Combination Lap/Shoulder Belt with Locking Latch Plate: Once it is buckled, this type of belt has a latch plate that will not allow the lap

portion of the belt to loosen. Belt is tightened by pulling hard on the shoulder portion of the vehicle belt while pushing down hard on the car

seat base.

• Combination Lap/Shoulder Belt with Sliding Latch Plate: This type of belt has a latch plate that slides freely along the belt. To prevent

movement of the lap portion of this type belt, the belt MUST be converted through the use of a Locking Clip, unless your vehicle belt can

beconvertedinanotherwayasdescribedinyourvehicleowner’smanual.

10 To install the locking Clip

• Tighten the buckled belt by pushing down hard on the doll carrier and base and pulling hard on the shoulder belt.

• While pushing down on the doll carrier and base, pinch the two straps together behind the buckle tongue. Unbuckle the belt without

allowing it to slip.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Joovy 003 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info