Bedienungsanleitung Joovy Scooter X2 807X (Seite 3 von 16) (Englisch, Französisch, Spanisch)

780390

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

EN FR ES

2 Unfolding the Stroller

• Keep children away from stroller while unfolding.

• Orient the stroller with the handlebar facing upward and closest to you.

• If necessary, release the folding lock located on the right side by lifting the lock off of the extended rivet. See Figure 2.1.

• Pull upwards on the handlebar until the stroller is completely opened and the latching mechanism on each side is engaged. See Figure

2.2.Becarefulnottoscratchtheoorwhenopeningthestroller.

• Visually check and gently push downward on the handlebar to ensure that the stroller is completely opened and locked before ANY use of

the product.

CAUTION:Whileunfoldingthestroller,becarefultokeepyourngersfrombeingpinchedbymovingparts.

!WARNING

ALWAYS keep children away from the stroller when unfolding.

Possible pinching hazard – Be careful when unfolding the stroller.

3 Installing the Rear Wheel Axle and Brake Set and Rear Wheels

• In a clean, dry place rest the stroller upside down with the rear legs facing upwards.

• Locate the rear axle and brake set and slide it onto the rear legs with the link brake facing the rear of the stroller. Be sure to slide each

side all the way on until the push pins are engaged in the holes of the plastic.

NOTE: You may need to push each of the push pins in to slide the plastic into place. See Figure 3.1.

• Pull upward on each side of the rear axle to ensure it is installed properly.

• Push the bar linking the brake levers into the disengaged position. See Figure 3.2.

To Install a Rear Wheel

• Locate a small washer and slide the washer onto the axle.

• Next place a rear wheel onto the axle over the small washer.

NOTE: The brake teeth on the wheel should be facing inward toward the brake lever.

• Then place one large washer onto the axle over the wheel.

• Next slide a spring washer onto the axle.

• Take another large washer and slide it onto the axle.

• Push the washers in to expose the axle hole. Then take one snap pin and insert the straight leg into the

smallholeintheaxle.Pushitrmlyintothisholeuntiltheroundportionoftheotherlegsnapscompletely

around the outside of the axle.

NOTE: The snap pin is curved (concave) to make insertion easier.

• Repeat the SAME installation sequence of washers, wheel, and snap pin for the remaining wheel.

• Install a hubcap onto each wheel by aligning the 5 tabs on the hubcap with the 5 slots in the wheel, and

then pushing it into place. Ensure that ALL 5 snaps have engaged securely and the hubcap cannot be

pulled off.

4 Rear Wheel Brakes

• The ScooterX2 comes equipped with a linked rear wheel brake system.

• To engage the rear wheel brakes, push down on one of the brake levers or the bar that connects the levers. See Figure 4.1. The stroller

may require slight forward or rearward movement in order to line up the teeth on the brake with each wheel brake cluster.

• Check that the brakes are properly applied by attempting to push the stroller backwards and forwards.

• To release the brakes, gently lift up on one of the brake levers or the bar that connects the levers. See Figure 4.2.

!WARNING

Always make sure the wheel brakes are engaged when the stroller is not being pushed so that the stroller will not roll

away. Never leave stroller unattended, especially on a hill or incline, as the stroller may tip over or slide.

5 Installing the Front Wheels

• Position the stroller so it is resting on the rear wheels and the handlebar. Locate one front wheel set and position the wheel set with the

swivel lock tab facing upward. Insert it onto a post located at the bottom front on one side of the stroller until an audible click is heard. See

Figure 5.1.

• Pull outward on the wheel set to ensure the wheel set is installed properly.

• Repeat this procedure for the other wheel.

• To remove a front wheel set, pull the metal ring at the bottom of the front wheel housing and slide the wheel set off of the post. See Figure

5.2.

Small Washer

Rear Wheel

Large Washer

Spring Washer

Snap Pin

Large Washer

REAR WHEEL SEQUENCE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Joovy Scooter X2 807X Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info