Bedienungsanleitung Jotul GF 400 (Seite 7 von 20) (Englisch)

467831

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Figure 7. Clearance to a combustible shelf.

Flue System Installation

Flue outlet (spigot) dimensions:

Internally = 128 mm

Externally = approx. 131 mm

When installing the vent, it is important to adhere to

national and local regulations that apply. Only one appli-

ance may be connected to the vent system.

The vent system must terminate above the roof.

The vent system and the flue pipe components must

be fastened to the stove with screws.

Minimum height of the chimney is approx. 2,15 m (7’)

and maximum height should not be more than approx.

10,7 m (35’). (When installation is at or above a height of

approx. 610 m (2000’), the chimney’s height must be at

least approx. 3,7 m (12’.) measured from the flue outlet. If

the chimney has to move through a horizontal distance,

make sure to use 45º or 90 º bends.

Max. number of 45º bends = 4

Max. number of 90º bends = 3

It is permitted to move the chimney a total of approx.

1,2 m (4’) horizontally.

An exhaust hood (terminal, cowl or rain cap) must be

mounted at the chimney’s termination point . After fit-

ting of the vent system and installation of the appliance,

carry out a smoke test on the flue as described in the

relevant section. If the appliance shuts off in operation

for no apparent reason (especially during windy or stormy

conditions) and will not relight, it is possible that the flue

system safety switch has operated. Allow the appliance

to cool down and relight. Any obstruction to the flow of

exhaust gases up the flue can cause this switch to operate

thereby making the situation safe. If the appliance cuts

out repeatedly, do not continue to use the appliance and

seek flue checking and service from qualified personnel

before re-using the appliance.

Closure Plate Installation

It is permissible to install this appliance using a closure

plate installation similar to traditional outset gas fires.

See diagrams (1 E-F) on page 28. The British Standards de-

tailing this type of installation are BS5871 pt1 and BS5440

pt 1. The appliance and flue must be sound and if used

with solid fuel or oil appliances it must be swept prior to

installation. There must be no other openings other than

the exit from the top of the flue and the opening into

which the appliance is being installed. All cracks, holes,

underfloor air vents etc must be removed and sealed fully

before installation continues. A proprietary metal flue box

complying with BS715 is a suitable appliance opening.

Figure 8. Vent height requirements.

Figure 9. Closure plate and flue requirements.







































Closure Plate

600 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jotul GF 400 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info