Bedienungsanleitung JRC JMA9932SA (Seite 67 von 404) (Englisch)

28346

Zoom out

Zoom in

Vorherige Seite

1/404

Nächste Seite

● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●

2-7

① Range selection

Changes the radar range.

“+”: Increases the range by one step. (The maximum range is 96 or 120 nautical miles.)

“-”: Decreases the range by one step. (The minimum range is 0.125 nautical mile.)

② RINGS indicator selection

Turns on and off the fixed distance scale display. When this is turned on, the intervals of the

range rings will be displayed. When this is turned off, then “OFF” will be displayed.

③ Pulse width selection

Select the pulse width. There are three pulse widths: Short pulse (SP), middle pulse (MP)

and long pulse (LP). The pulse widths that can be used depend on the range being used. If a

change cannot be made, then nothing will be displayed. This setting is stored for each range.

④ Tuning indicator mode

Sets the tuning mode to MANUAL or AUTO.

MANUAL → AUTO

（Manual tuning）→（Automatic tuning）

⑤ Bearing mode selection

This has the same function as the [AZI MODE] switch. It switches between North-up (true

bearing), Head-up (relative bearing) and Course-up. Each time this button is clicked it will step

through the settings in the following order: “N UP” ⇒ “C UP” ⇒ “H UP”

⑥ Motion mode selection

The screen display is changed between the True Motion (TM) and Relative Motion (RM)

displays. Clicking this button will switch between “TM” and “RM.” (R) indicates a relative trail.

(T) indicates a true trail.

⑦ Transmission/Standby selection

About three minutes after the [PWR] switch is turned on, the “PREHEAT” indication on the upper

left of the screen will change to “STANDBY.”

STANDBY: Indicates that the unit is in the standby state. Clicking the switch at this time will

change the unit to the transmission state.

TRANSMIT: Indicates that the unit is in the transmission state. Clicking the switch at this time

will change the unit to the standby state.

⑧ Change Interswitch connection

This is displayed if Interswitch is connected. The indicator shows the connected scanner and

the connection status of the indicator. When this switch is pressed, a menu to change the

connection states of the scanner and indicator will be displayed. The scanner and indicator

connection states cannot be changed, unless the master indicator is in the standby state.

⑨ AIS target refreshed (ACT)

When this switch is pressed, the AIS target will be activated.

⑩ AIS target deactivated (DACT)

When this switch is pressed, the activated AIS target is paused.

⑪ ARPA symbol indicator selection

Turns the ARPA symbol indicator on or off. The setting is changed each time this button is

clicked.

⑫ AIS symbol indicator selection

Turns the AIS symbol indicator on or off. The setting is changed each time this button is

clicked.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JRC JMA9932SA Seite 67

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info