28360

JRC Radar2000 Seite 18

18
Zoom out
Zoom in
Vorherige Seite
1/54
Nächste Seite
11
3.4 MOUNTING THE SCANNER UNIT
INSTALLATION
Selecting an adequate location for the scanner unit requires careful consider-
ation. On many small vessels, the unit can be installed on a mast platform, on
an arch, or on a bridge structure near the ship’s center line.
The radiator beam should not be obstructed by nearby large objects. Locate the
unit where large structures such as superstructures, searchlight, horns or masts
are not in the same horizontal plane, otherwise, blind areas and false targets can
appear on the radar screen.
Using the template provided in the front of manual as a guide, prepare the mount-
ing surface with the four mounting holes as required. Install the Radome and
secure it to the mounting surface. The correct mounting hardware is stainless
steel hexhead bolts
5
/16”, 1
1
/4” long with 18 UNC thread. A flat and lock washers
should be used. The Radome should be parallel to the ship’s waterline and ori-
ented so the cable inlet is pointed AFT.
When mounting the Radome to a platform attached to a fly bridge, or super-
structure, avoid placing the Radome Unit at eye level. Although the radar trans-
mits a 2.0 kW peak power the average power radiated is less than 0.5 W. There-
fore, the hazard from RF radiation levels is virtually nonexistent beyond 2 feet
from the Radome Unit.
However, due to the sensitivity of the human eye, it is recommended and pru-
dent to install the Radome in a plane above or below the passengers line-of-
sight.
When the sickness of the mounting base is more than 0.4 inches, the longer
bolts are required. In this case, the bolts length is as follows;
Bolt length (inch) ≦ 1.25 + sickness of mounting base (inch)
If the longer bolts are used, the modulator PCB could potentially damaged.
When installing an aerial,make a hole for the water pulling-out.
The equipment sometimes becomes breaking cause because it is
flooded when getting a hole for the water pulling-out without
making it.
CAUTION
11
3.4 MOUNTING THE SCANNER UNIT
INSTALLATION
Selecting an adequate location for the scanner unit requires careful consider-
ation. On many small vessels, the unit can be installed on a mast platform, on
an arch, or on a bridge structure near the ship’s center line.
The radiator beam should not be obstructed by nearby large objects. Locate the
unit where large structures such as superstructures, searchlight, horns or masts
are not in the same horizontal plane, otherwise, blind areas and false targets can
appear on the radar screen.
Using the template provided in the front of manual as a guide, prepare the mount-
ing surface with the four mounting holes as required. Install the Radome and
secure it to the mounting surface. The correct mounting hardware is stainless
steel hexhead bolts
5
/16”, 1
1
/4” long with 18 UNC thread. A flat and lock washers
should be used. The Radome should be parallel to the ship’s waterline and ori-
ented so the cable inlet is pointed AFT.
When mounting the Radome to a platform attached to a fly bridge, or super-
structure, avoid placing the Radome Unit at eye level. Although the radar trans-
mits a 2.0 kW peak power the average power radiated is less than 0.5 W. There-
fore, the hazard from RF radiation levels is virtually nonexistent beyond 2 feet
from the Radome Unit.
However, due to the sensitivity of the human eye, it is recommended and pru-
dent to install the Radome in a plane above or below the passengers line-of-
sight.
When the sickness of the mounting base is more than 0.4 inches, the longer
bolts are required. In this case, the bolts length is as follows;
Bolt length (inch) ≦ 1.25 + sickness of mounting base (inch)
If the longer bolts are used, the modulator PCB could potentially damaged.
When installing an aerial,make a hole for the water pulling-out.
The equipment sometimes becomes breaking cause because it is
flooded when getting a hole for the water pulling-out without
making it.
CAUTION
… 18 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JRC Radar2000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info