Bedienungsanleitung JRpropo XG14 (Seite 14 von 112) (Englisch)

606954

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

▋Binding▋Procedure▋

▋(pairing▋the▋transmitter▋and▋receiver)

In order for the transmitter and receiver to communicate, it is essential to pair or bind them together.

Please follow this procedure:

1) Be sure that remote antenna unit is properly connected

to the receiver. Locate the included bind plug, and ensure

the transmitter and receiver batteries are fully charged.

※ Note that the Remote Antenna acts as both a receiver and

also transmits data back to the transmitter. Carefully

note the orientation of the antenna within the remote

unit. This orientation is extremely important.

2) On the transmitter access the “BIND & RANGE” menu

under the System List.

RefertothePage78"BindandRangeCheck【BIND&RANGE】"

3) Inserting the bind plug into the bind terminal of the

receiver and connect the battery to a spare channel (such

as the AUX channel) - the LED’s on the receiver and the

remote antenna will begin to blink (Ready to Bind).

Note:

Be sure to insert the bind plug before connecting the

battery.

4) Refer to the “BIND & RANGE CHECK” Screen in the

transmitter System Setting mode. Press the dial to start

the binding process.

5) ‘Binding’ will flash on the transmitter display, and

upon completion of the binding process, it will display

“SUCCESS ! PLEASE CHECK FAIL SAFE”. Concurrently,

both receiver’s LED’s will stop flashing and be solid –

signifying completion of the bind process. Disconnect the

bind plug from receiver, disconnect the receiver battery

and switch o󰮏 transmitter. If the LED’s continue to blink,

repeat the procedure from the beginning.

6) Lastly, connect a servo, turn on the transmitter then

receiver, and confirm that communications have been

established.

RangeCheck

This checks the performance of the transmitter by lowering

the power output to simulate a long distance range test.

Under the” Bind & Range Check” setting screen, move the

cursor to the POWER: NORMAL column and change it to

LOW. The transmitter LED shall ash Blue to indicate it is

set to low power mode. When in this mode, walk a distance

of approximately 40m from the aircraft and conrm that the

transmitter operates the aircraft normally. Continue testing

as you walk around the aircraft.

RefertothePage78"Bind

andRangeCheck【BIND&RANGE】"

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters　　　

Connecting

the battery to a

spare channel

(such as AUX

channel)

Location of LED light

Binding terminal

Bind plug

RefertothePage89"Failsafe【FAILSAFE】"

1. Are the transmitter and receiver batteries fully charged?

2. Is the remote antenna securely connected?

3. Is the distance between the transmitter and receiver too close?

4. When the procedure is carried out on the top of a desk or

bench top that is made from metal, the binding procedure

may not be successful.

If the bind process or range check is not successful,

check the following items:

Please note that when the model or model type is

changed in the transmitter, re-binding will be required.

Never ﬂy the aircraft in Range Check mode.

Be sure that the failsafe settings are set in the

transmitter.

40 meters　　　

Connecting

the battery to a

spare channel

(such as AUX

channel)

Location of LED light

Binding terminal

Bind plug

Preparation

XG14English.indd 12 2013/07/16 16:39

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JRpropo XG14 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info