Bedienungsanleitung JRpropo XG14 (Seite 34 von 112) (Englisch)

606954

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

▋Gyro▋Sensitivity【GYRO▋SENS】

▋▋Function▋Explanation

This function controls the gyro sensitivity using the GEAR channel, and the Auxiliary (AUX)

channel if required. It allows adjusting the gyro sensitivity from the transmitter. Further, it

supports “Dual Gain” as employed in JR’s G7000 where two channels are required. Additionally,

the use of two gyro units is also possible. In addition, it supports 3 axis gyros (such as JR

TAGS01), with separate gains for yaw, pitch and roll axis. The sensitivity switching of each gain

can be with individual switches, or combined using the Flight Mode switch.

▋▋Setting▋Method

It is necessary to allocate the Gyro Sensitivity to a channel using “DEVICE SELECT” in the System List. Set “OUT”

as “GYRO” by activating the function.

Select the switch position for changing the gyro sensitivity and move the cursor to each position to set the

sensitivity on the display. If “AUTO” is selected, the sensitivity switching setting for each flight mode will be

applied.

There are two gyro sensitivities available - “NORMAL” and Tail Lock (T.LOCK) - choose the type depending on

your application.

⿟ Gyro sensitivity Switching delay (DELAY)

To avoid excessive servo hunting when switching

the gyro sensitivity from a low sensitivity to

higher sensitivity setting, (e.g. when the main

rotor blade rpm is not stable) it is possible to set

a delay on this function.

Note: During switching, the time will be delayed

only in the high sensitivity direction.

⿟ Trim Input Function (TRIM IN)

By using the Trim Input, it is possible to change

the gyro sensitivity values using a Trim Lever.

Therefore, it is possible to easily adjust the sensitivity during ight.

⿟ When two individual channels have been selected for Gyro sensitivity, it is possible to select from the following two

modes.

፧

"TWO GYRO"

It is possible to allocate two individual gyro sensitivities, and the Gyro sensitivity switching can occur on one

shared switch.

፧

"DUAL GAIN"

In this mode, one channel is allocated for “NORMAL” and the other channel to “TAIL LOCK SENSITIVITY”.

※ For 3 Axis gyro applications (such as the JR TAGS01) three separate gain channels can be used. Each

sensitivity for yaw, pitch and roll axis can be set using individual switches, or combined onto the ight mode

switch. The gyro sensitivities can also be changed to Normal or Stunt Modes when using the JR TAGS01.

⿟ “Calibration for 3 Axis Gyros”

The JR 3 Axis Gyro system (TAGS01) as used for Flybarless R/C helicopters requires “CALIBRATION” prior

to ying. This is required to recognize the type of CCPM being employed, and learn the servo travel ranges

used. Calibration requires precise gimbal stick movement of one function at a time (Elevator or pitch stick up

& down, and Aileron stick right to left). If, for example, the aileron stick is pushed by mistake during elevator

calibration, the calibration will be incorrect. In order to avoid this problem, the calibration function allows

single channel calibration.

Function▋List

Helicopter

Airplane

DANGER

WARNING

CAUTION

Glider

Sensitivity Switching delay

If AUTO is selected, the sensitivity

switching setting for each Flight

Mode will be applied.

Further, by operating the switch

that you wish to use, input will be

automatically carried out.

Display for corresponding

flight mode

Gyro Mode selection

S = STUNTT = TAIL LOCKN = NORMAL

Gyro sensitivity (T.LOCK)

Calibration function

TRIPLE AXIS MODE

Setting values and actual output values

NORMAL

-150% -100% -50% 0% 50% 100% 150%

0% 50% 100% 125%

T.LOCK

-150% -100% -50% 0% 50% 100% 150%

0% 50% 100% 150%

-150% -100% -50% 0% 50% 100% 150%

0%50%100%150%

TRIPLE AXIS

-150% -100% -50% 0% 50% 100% 150%

0% 50% 100% 150%

-150% -100% -50% 0% 50% 100% 150%

0%50%100%150%

DUAL GAIN

NORM GAIN

T.LOCK

-150% -100% -50% 0% 50% 100% 150%

0% 50% 100% 125%

0% 50% 100% 150%

-150% -100% -50% 0% 50% 100% 150%

The upper numerical values are the

setting values.

Sensitivity Switching delay

If AUTO is selected, the sensitivity

switching setting for each Flight

Mode will be applied.

Further, by operating the switch

that you wish to use, input will be

automatically carried out.

Display for corresponding

flight mode

Gyro Mode selection

S = STUNTT = TAIL LOCKN = NORMAL

Gyro sensitivity (T.LOCK)

Calibration function

TRIPLE AXIS MODE

Setting values and actual output values

NORMAL

-150% -100% -50% 0% 50% 100% 150%

0% 50% 100% 125%

T.LOCK

-150% -100% -50% 0% 50% 100% 150%

0% 50% 100% 150%

-150% -100% -50% 0% 50% 100% 150%

0%50%100%150%

TRIPLE AXIS

-150% -100% -50% 0% 50% 100% 150%

0% 50% 100% 150%

-150% -100% -50% 0% 50% 100% 150%

0%50%100%150%

DUAL GAIN

NORM GAIN

T.LOCK

-150% -100% -50% 0% 50% 100% 150%

0% 50% 100% 125%

0% 50% 100% 150%

-150% -100% -50% 0% 50% 100% 150%

The upper numerical values are the

setting values.

XG14English.indd 32 2013/07/16 16:40

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JRpropo XG14 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info