Bedienungsanleitung JRpropo XG14 (Seite 38 von 112) (Englisch)

606954

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

▋Throttle▋trim【THRO▋TRIM】

▋▋Function▋Explanation

This function sets the Throttle Trim movement, and additionally a Throttle Cut function is

provided for cutting the engine. There is a Trim Memory function for cutting the engine using

the Trim. Note that for airplanes, an Idle Adjust function is also incorporated that allows

separate detailed setting of the idle position.

▋▋Setting▋Method

If the Throttle Cut is set to ACT, the Trim Memory will be forcibly set to INH. On the screen rotate the dial to

move to and select (inverse display), then press the dial to set the item.

⿟ Throttle Cut Function (THRO CUT)

The Throttle cut can be used by setting it to “ACT”. Initially the switch is allocated to “TRN SW”, POS1. It is

possible to allocate this switch to any desired switch location. Set the Throttle Cut to the desired position.

፧

Time Lag (TIME LAG)

This function is to avoid the sudden stopping of the engine if the throttle cut switch is activated in error.

This is especially useful when using the momentary switch (Trainer switch). It is possible to use this

momentary switch as timer switch at the same time as throttle cut. When the time lag function is activated,

throttle cut only activates when the switch is held on for a certain duration. The timer can be activated by

a momentary action as usual. The time lag duration can be set between 0.5 to 2 seconds.

⿟ Throttle Trim Memory (THRO TRIM MEMORY)

When the Trim is lowered in a single action, the trim position immediately prior to the movement will be

memorized, and when the trim is raised again, the trim will automatically return to the memorized position.

The memorized position will be marked on the Trim display.

⿟ Idle Adjust (IDLE ADJUST)

※ For Airplane Mode only

The idle position when the throttle

stick is at the “Slow” position can be

given a separate setting using a switch.

It is possible to set up landing with idle

“DOWN”, and normal flying with idle

“UP”.

⿟ Please carefully conrm the linkage does not jam when the carburetor is closed.

▋▋Caution▋Note

⿟ Throttle Cut will only work when the helicopter Flight Mode is set to “NORMAL”.

Helicopter

Airplane

DANGER

WARNING

CAUTION

Glider

Function▋List

Throttle Cut

Time Lag

Function Operation Condition

In order to use the function,

INH should be changed to ACT

In order to use the function, after setting

the Throttle Cut function to INH, set the

Trim Memory to ACT in this function.

Idling Point Adjustment

Throttle Cut

Time Lag

Function Operation Condition

In order to use the function,

INH should be changed to ACT

In order to use the function, after setting

the Throttle Cut function to INH, set the

Trim Memory to ACT in this function.

Idling Point Adjustment

ダイヤル

TIPS

調整ポイント表示

ポイント接続を曲線に変更スティック入力位置と出力位置の数値表示

現在の

フライトモード位置

各調整ポイントの

入力位置と出力位置

ポイントの

追加と削除

注意：

グラフはホバリン

グスロットルやス

ロットルトリムで

変化する場合もあ

ります。

カーブをコピー

XG14English.indd 36 2013/07/16 16:40

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JRpropo XG14 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info