Bedienungsanleitung Juki DDL8700B-7 (Seite 42 von 51) (Englisch)

614555

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

– 40 –

⑭ Function of stop immediately after the reverse feed stitching at the start of sewing (Function set-

ting No. 60)

This function temporarily stops the sewing machine even when keeping depressing the front part of the

pedal at the time of completion of process of reverse feed stitching at the start of sewing.

It is used when sewing a short length by reverse feed stitching at the start of sewing.

0 : Not provided with the function of temporary stop of the sewing machine immediately

after the reverse feed stitching at the start of sewing

1 : Provided with the function of temporary stop of the sewing machine immediately after

the reverse feed stitching at the start of sewing

Stop the sewing machine

temporarily to change

direction of sewing products.

⑮ Function of soft-down of presser foot (with AK device only) (Function setting No. 70 and 49)

This function can softly lower the presser foot.

This function can be used when it is necessary to decrease contact noise, cloth defect, or slippage of cloth

at the time of lowering the presser foot.

Note : Change the time of function setting No. 49 together at the time of selecting the function of soft-

down since the sufcient effect cannot be obtained unless the time of function setting No. 49

is set longer when lowering the presser foot by depressing the pedal.

Setting range : 0 to 500 ms <10 ms/Step>

0 : Function of soft-down of presser foot is not operative. (Presser foot is rapidly lowered.)

1 : Selection of function of soft-down of presser foot

⑯

Function of reducing speed of reverse feed stitching at the start of sewing (Function setting No. 92)

Function to reduce speed at the time of completion of reverse feed stitching at the start of sewing :

Normal use depending on the pedal condition (Speed is accelerated to the highest without a break.) This

function is used when temporary stop is used properly. (Cuff and cuff attaching)

0 : Speed is not reduced.

1 : Speed is reduced.

Sew without stopping

without a break.

Temporary stop

⑰ Retry function (Function setting No. 73)

When the retry function is used, if the sewing material is thick and not pierced with needle, this function

makes the needle pierce in the material with ease.

0 : Re-try function is not provided.

1 to 10 : Re-try function is provided. (Needle-bar returning force before re-trying: 1 (small) -

10 (large))

⑱ Presser foot lifting solenoid suction time setting (Function setting No. 84)

Suction time of presser foot lifting solenoid can be changed. When heating is great, it is effective to lessen

the value.

(Caution) When the value is excessively small, malfunction will be caused. So, be careful when chang-

ing the value.

Setting range : 50 to 500ms <10/ms>

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Juki DDL8700B-7 Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info