Bedienungsanleitung Junkers MB LAN (Seite 6 von 36) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

519378

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Installation

MB LAN – 6 720 802 641 (2012/08)

2.3 Specification

3Installation

3.1 Installation

B Removing the cover (Æ Fig. 3, page 32)

B Fitting the module (Æ Fig. 4, page 32)

B Fixing the module (Æ Fig. 5, page 32)

3.2 Electrical connections

Connections and interfaces

Legend to Fig. 6, page 33:

7,5 V DC Power supply unit connection

HT 2-wire BUS system connection

LAN LAN connection (RJ45)

RESET RESET button

Pre-assembling the grommets and connecting the cables

B Open out the grommets to match the cable diameter and make an

incision on one side (Æ Fig. 7, page 33).

B Fit the grommets and connect the cables (Æ Fig. 8, page 33).

BUS connection

B Connect BUS subscribers with two BUS connectors in series

(Æ Fig. 6, page 33) or BUS subscriber [B] with one junction box [A]

in a star configuration (Æ Fig. 9, page 33).

B All LV leads must be routed separately from cables carrying mains

voltage to avoid inductive interference (minimum separation

100 mm).

B In case of external inductive interference, shield the cables.

This ensures that the cables are shielded from external interference

(e.g. heavy current cables, overhead wires, transformer stations,

radio and television set, amateur radio stations, microwave ovens

etc).

B Fit the cover and plug in the power supply unit supplied.

4 Commissioning

The router must be configured as follows:

• DHCP enabled

• Ports 5222 and 5223 not blocked

• Free IP address available

• Address filtering (MAC filter) matched to the module.

The module automatically obtains an IP address from the router. The

name and address of the target server are stored in the standard settings

of the module. If there is an internet connection, the module

automatically logs into the Junkers-Server.

The router does not necessarily have to be connected to the internet.

The module can also be operated using the local network only. If this is

the case, access to the heating system via the internet or automatic

updates of the module software are not possible.

The first time the JunkersHome App starts, you will be prompted to

enter the factory-set login name and password. These login details are

printed on the module data plate.

Data plate

Legend to Fig. 10, page 33:

[1] Data plate with login details, MAC address and serial number

[2] DIP switch (no function)

Testing the connection (with heating circuit 1 logged on)

You can check whether the module is communicating correctly with the

heating system.

B Press the RESET button (Æ Fig. 6, page 33)briefly in order to change

the operating mode for heating circuit 1 at the controller.

The controller display shows the modified operating mode (heating

or economy ).

B To conclude the connection test, reinstate the required operating

mode.

Resetting personal settings

If you have forgotten your personalised login name or password:

B Hold down the RESET button (Æ Fig. 6, page 33) for at least 5

seconds.

The factory-set login details are restored.

5 Environmental protection/Disposal

Environmental protection is a key commitment of the Bosch Group.

Quality of products, efficiency and environmental protection are equally

important objectives for us. Laws and regulations aimed at protecting

the environment are strictly adhered to.

To protect the environment we will, subject to economical aspects, use

the best possible technology and materials.

Packaging

We participate in the recycling programmes of the countries in which our

products are sold to ensure optimum recycling.

All of our packaging materials are environmentally compatible and can

be recycled.

Specification

Dimensions (W×H×D) 151×184×61mm (further

dimensions Æ Fig. 2, page 32)

Maximum cross-section

(terminals)

2.5 mm

Rated voltages:

• BUS

• Module power supply

• 12 V to 15 V DC (reverse polarity

protected)

• Plug power supply unit supplied

230 V AC/7.5 V DC, 700 mA

Interfaces • 2-wire BUS

• LAN: 10/100 MBit/s (RJ45)

Power consumption 1.5 VA

Permissible ambient

temperature

0 ... 50 °C

IP rating IP20

Table 2

If the maximum cable length of the BUS connection

between all BUS subscribers is exceeded, the system

cannot be commissioned.

Cable length Conductor cross-section

≤ 80 m 0.40 mm

≤ 100 m 0.50 mm

≤ 150 m 0.75 mm

≤ 200 m 1.00 mm

≤ 300 m 1.50 mm

Table 3 Total BUS length

During commissioning, the LED on the module

illuminates in red if neither the BUS nor the LAN

connection is made.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Junkers MB LAN Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Junkers MB LAN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info