Bedienungsanleitung Just Fire NB-B18 (Seite 10 von 41) (Englisch)

656266

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

PELLET BURNING STOVES

INSTALLATION AND MAINTENANCE MANUAL

compromising thermodynamic performance, however it is required that the conditions still guarantee about 50 m³ / h of air

replacement, as provided in the current UNI 10683 .

2.5. CONNECTION OF SMOKE DISCHARGE PIPE

When making the hole for the flue pipe it must be taken into account the possible

presence of inflammable materials. If the hole has to go through a wood wall or other

thermo labile material , the installer MUST use the Industrial insulated pipe (with min

thermal conductivity of 0.07 W / m ° K). The same applies if the stove pipe must go vertical

or horizontal sections remain near (min.20cm) to a heat-labile wall.

The combustion chamber works in depression, so the exhaust duct for the exhaust fumes

will be linked to depression when effective chimney as prescribed.

It should always use pipes and fittings with appropriate seals to ensure

air-tightness in order to avoid possible harmful CO fumes into the environment.

All sections of the exhaust duct must be inspectable and removable to

allow for periodic cleaning of the interior, which is necessary for the proper functioning

of the system (T-piece with inspection). Position the stove strict accordance with all

regulatory requirements and attention to highlighted date.

IMPORTANTE!

All changes direction 90 degrees of the flue gas channel must be prepared if possible

with the appropriate fittings to "T" with inspection. It is absolutely forbidden to use a

net at the end of the hose as it can cause serious problems for the proper and safe operation of the stove.

In connection do not use the chimney sections of pipe horizontally, but always the same place at an angle of 5° minimum to

rise, possibly avoiding the use of a 90-degree (you can use upto 3), and use preferably 45 ° curves. It is recommended to not

use a total length of the pipe diameter 80 mm, greater than 6 m in total.

2.6. CONNECTION TO THE CHIMNEY

The chimney must have inside dimensions of no more than cm. 20X20 or 20 cm

diameter. In the case of larger or poor condition of the chimney (ie: cracks, poor

insulation, etc.) it is recommended to insert stainless steel tube in the chimney of a of

suitable diameter for its entire length, to the very top. Check with suitable

instruments that there is a minimum draft. Guaranteed 15 Pa. At the bottom of a

chimney inspection for periodic inspection and cleaning, which must be done

annually. You must ensure that a chimney top is installed according to regulations for

wind force.

This type of connection must guarantee of 15 Pa, allows the correct discharge of

smoke with a natural draft even if there is no electricity.

2.7. CONNECTION TO AN EXTERNAL FLUE PIPE WITH ISOLATED OR DOUBLE WALL

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Just Fire NB-B18 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info