Bedienungsanleitung JVC CU-VD40 (Seite 23 von 28) (Englisch)

56182

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Troubleshooting

Tr o ub le Cause/Action

General

Cannot turn the power on.

z Make sure the AC adapter and power cord are connected properly.

The burner or AC adapter is hot.

z This is not a malfunction.

z If the burner is abnormally hot, remove the AC adapter and consult

the dealer from which you purchased the burner.

After pressing the power button, it takes

approximately 20 seconds before the burner

becomes operable.

z This is not a malfunction.

Malfunction or error occurs.

z Turn the burner off, and then turn it back on again.

Saving

The Everio camera is not recognised.

z Make sure the USB cable is connected properly. Install the projected

end of the terminal to the burner and the other end to the Everio

camera.

The PC is not recognised.

z Make sure the USB cable provided for the Everio camera is connected

properly.

Cannot open the disc tray.

z A disc cannot be ejected by pressing the eject button if data is being

written to the disc. Wait until writing finishes.

z If a disc cannot be ejected with the eject button because of a failure

or a malfunction caused by, for example, the burner being dropped,

insert a thin rod of about 10 cm long into the force eject hole to eject

the disc. (0P11)

Reading fails.

z Insert the disc with the label facing up.

z Make sure the disc tray is not dirty.

z Make sure the writing surface of the disc is not damaged.

z Make sure that special-shaped discs are not used.

z Any CD that does not comply with standards such as the CD-DA

standard (copy-control CDs) cannot be played.

z For CD-R or CD-RW, make sure it is not recorded using the packet-

write method.

Writing fails.

z Make sure an appropriate disc is being used. (0P25)

z Use discs recommended for the burner. (0P26)

z Make sure that a new disc is used for DVD-R.

z Insert the disc with the label facing up.

z Make sure the disc tray is not dirty.

z Make sure the writing surface of the disc is not damaged.

z Make sure that special-shaped discs are not used.

It is impossible to dub the DVD discs, which were

written with this burner, on a HDD-DVD recorder.

z Connect the burner to the Everio camera, playback using “PLAY

DVD” function of the camera, and dub the DVD discs with the DVD

recorder. (Refer to the instruction manual of Everio.)

Writing/reading at maximum speed is not possible

(when connected to PC).

z Make sure an appropriate disc is being used. (0P25)

z Use discs recommended for the burner. (0P26)

z Make sure a proper standard disc is being used. (Writing/reading at

maximum speed may not possible if non-standard discs are used.)

Playback

The remote control is not working.

z Remove the batteries, insert them again and operate the remote

control.

z Replace with new batteries.

Unable to operate.

z Operation may be prohibited due to the disc or other conditions.

z If the burner does not work at all, turn off the power and turn it on

again. (It may not work properly due to lightning strike or static

electricity.)

CU-VD40E_EN.book Page 23 Wednesday, June 6, 2007 10:40 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC CU-VD40 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC CU-VD40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info