Bedienungsanleitung JVC DDX630 (Seite 67 von 80) (Englisch)

521282

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

English 67

Accessories/Installation Procedure

Accessories

..........1

..........1 (2m)

..........8

..........1 (3m)

DDX630WBT/

DDX630WBTM only.

Installation Procedure

1 To prevent a short circuit, remove the key

from the ignition and disconnect the

battery.

2 Make the proper input and output wire

connections for each unit.

3 Connect the speaker wires of the wiring

harness.

4 Connect the wiring harness wires in the

following order: ground, battery, ignition.

5 Connect the wiring harness connector to

the unit.

6 Install the unit in your car.

7 Reconnect the

- battery.

8 Press the reset button.

9 Perform the Initial Setup.

2WARNING

•

If you connect the ignition wire (red) and the

battery wire (yellow) to the car chassis (ground),

you may cause a short circuit, that in turn may

start a fire. Always connect those wires to the

power source running through the fuse box.

• Do not cut out the fuse from the ignition wire

(red) and the battery wire (yellow). The power

supply must be connected to the wires via the

fuse.

After the Installation

After the installation, perform the Initial Setup

by referring to the instruction manual.

• Mounting and wiring this product requires

skills and experience. For best safety, leave the

mounting and wiring work to professionals.

• Make sure to ground the unit to a negative 12V

DC power supply.

• Do not install the unit in a spot exposed to direct

sunlight or excessive heat or humidity. Also avoid

places with too much dust or the possibility of

water splashing.

• Do not use your own screws. Use only the screws

provided. If you use the wrong screws, you could

damage the unit.

• If the power is not turned ON (“Miswiring

DC Offset Error”, “Warning DC Offset Error” is

displayed), the speaker wire may have a short-

circuit or touched the chassis of the vehicle and

the protection function may have been activated.

Therefore, the speaker wire should be checked.

• If your car’s ignition does not have an ACC

position, connect the ignition wires to a power

source that can be turned on and off with the

ignition key. If you connect the ignition wire to

a power source with a constant voltage supply,

such as with battery wires, the battery may be

drained.

• If the console has a lid, make sure to install the

unit so that the faceplate will not hit the lid when

closing and opening.

• If the fuse blows, first make sure the wires aren’t

touching to cause a short circuit, then replace the

old fuse with one with the same rating.

• Insulate unconnected wires with vinyl tape or

other similar material. To prevent a short circuit,

do not remove the caps on the ends of the

unconnected wires or the terminals.

• Never cut away cable insulation to make the

proper connections may result in fire or product

damage.

• Connect the speaker wires correctly to the

terminals to which they correspond. The unit may

be damaged or fail to work if you share the -

wires or ground them to any metal part in the car.

EN_LVT2272-001A_MX_200mm.indb 67EN_LVT2272-001A_MX_200mm.indb 67 11/12/15 13:0411/12/15 13:04

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC DDX630 Seite 67

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info