Bedienungsanleitung JVC DR-MH30 (Seite 81 von 92) (Englisch)

57386

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Masterpage:Right0

EN 81

Filename [MH30_20S_12Subsidiary.fm]

Page 81Thursday, 7 April 2005 10:14

TROUBLESHOOTING

Before requesting service for a problem, use this chart and see if

you can solve the trouble yourself. Small problems are often easily

solved, and this can save you the trouble of sending your unit off

for repair.

Initialising (DVD Deck Only)

N Press A to turn off the unit, press and hold A, then press o

for two seconds or more.

General

● The AC power plug is disconnected from the mains outlet.

N Connect the AC power plug to the mains outlet securely.

(A pg. 16)

N Remove the batteries, wait for 5 minutes or more, then load the

butteries again.

● The setting of the remote control code is inappropriate.

N Set the same remote control code (1, 2, 3, or 4) on both the unit

and the remote control. (A pg. 66)

● The batteries are discharged.

N Replace the dead batteries with new ones.

● The source (another video recorder, camcorder) has not been

properly connected.

N Confirm that the source is properly connected.

● All necessary power switches have not been turned on.

N Confirm that all units’ power switches are turned on.

● The setting of the input channel position is inappropriate.

N Select the input channel position (AF-1B, AL-1B or AL-2B) that

corresponds to the input terminal connected to the external

equipment. (A pg. 63)

N Set ASUPERIMPOSEB to AOFFB. (A pg. 72)

● There are cases when the operation is prohibited on the disc.

● Lightning or static electricity may cause malfunction of the unit.

N Press A to turn the power off, then press the button again to

turn the power on.

● The setting of the remote control code is inappropriate.

N To operate the unit using a JVC TV remote control, set the

remote control code of the unit to A1B (Default: A3B). (A pg. 66)

Playback (DVD Deck)

● The DVD deck is not selected.

N Press DVD so that the DVD lamp lights up on the unit.

● The TV receiver’s channel selector is not set to the AV mode.

N Set the TV to its AV mode.

● When interlace scanned programme is played back,

progressive scan mode is selected.

N Press and hold PROGRESSIVE SCAN until q disappears

from the front display panel. (A pg. 72)

● The disc is loaded upside down.

N Place the disc on the disc tray with the playback surface facing

down. (A pg. 8)

● A disc not being compatible with the unit is loaded.

N Load a playable disc on the unit. (A pg. 5)

● A dirty disc is loaded.

N Clean the disc. (A pg. 9)

● Defective disc is loaded.

N Replace the warped or scratched disc with a normal one.

N Images are blurred or distorted at the point where the playback

speed changes and this is not a malfunction of the unit.

N Playback does not start for approximately 30 seconds after

recording is stopped and this is not a malfunction of the unit.

● The Parental Lock is engaged and the disc is rated higher than

the set level.

N Release the Parental Lock temporarily or change the set level.

(A pg. 34)

Playback (HDD Deck)

● The HDD deck is not selected.

N Press HDD so that the HDD lamp lights up on the unit.

Recording (DVD Deck)

● The channel position does not correspond to that in the

receiving area.

N Set the correct channel position for the receiving broadcast.

(A pg. 73)

● No disc or a disc not being compatible with the unit is loaded.

N Load a recordable disc on the unit. (A pg. 5)

● The disc loaded is not formatted.

N Format the disc. (A pg. 78)

● A finalised DVD-R disc is loaded.

N Recording cannot be made on finalised discs. Load a

recordable disc on the unit.

● The disc is full or does not have enough space for the title to be

recorded.

N Clear unnecessary titles on the disc or load a blank disc.

(A pg. 52)

● The DVD-RAM disc loaded has had its protect tab slid to the

protect position.

N Release the protect tab. (A pg. 8)

Malfunction occurs on the unit.

No power is supplied to the unit.

The remote control does not work properly.

Dubbing from the external equipment is not possible.

The on-screen display superimposed on the programme

played back/received on this unit is recorded when you dub

the programme to an external recording equipment.

The unit does not operate.

The remote control of a JVC TV will not operate the unit.

The DVD deck cannot be operated.

Images do not appear on the TV screen.

Playback does not start or stop immediately after playback is

started by pressing I.

On the front display panel, ANO DISCB appears.

Images are blurred or distorted when you start High-Speed

Search.

Playback does not start.

Playback does not start when you select a title or a chapter.

The HDD deck cannot be operated.

The desired programme cannot be recorded.

Recording cannot be made.

MH30_20S_00.book Page 81 Thursday, April 7, 2005 10:14 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC DR-MH30 Seite 81

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC DR-MH30

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info