20741
99
Zoom out
Zoom in
Vorherige Seite
1/112
Nächste Seite
Masterpage:Right-No-Heading
EN 99
Filename [DR-M10U_11Subsidiary.fm]
Page 99 March 5, 2004 11:53 am
DISPLAY SET
(The boldface settings in the table below indicate the settings at your purchase.)
8 SUPERIMPOSE
OFF
AUTO
When “SUPERIMPOSE” is set to “AUTO” and ON SCREEN on the Remote is
pressed, various operational indicators appear on the TV screen. To clear the
operational indicators, press ON SCREEN again.
You can select the modes of indications superimposed on the TV screen.
OFF:
To turn off superimposed indications.
AUTO:
To superimpose operational indications for approximately five
seconds just after the corresponding operation.
NOTES:
When you use this unit as the source player for editing, be sure to set “SUPERIMPOSE”
to “OFF” before starting. (
pg. 89, “Edit To Or From Another Recorder”)
When you select “AUTO”, during playback, the operation mode indicators may be
disturbed depending on the type of disc being used.
8 GRAY BACK
OFF
ON
When this function is set to “ON”, the TV screen becomes all grey when
receiving a channel not in use.
NOTE:
When you want to receive an unstable channel with poor signals, set this function to
“OFF”.
8 DIMMER
BRIGHT
DIMMED1
DIMMED2
OFF
You can change the brightness of the front display panel.
BRIGHT:
Normally select this.
DIMMED1/DIMMED2:
To change the brightness level. (Blue lamp on the front display panel
become dimmer.)
OFF:
To dim the front display panel. (Blue lamp on the front display panel
is turned off.)
NOTE:
It is impossible to turn off the light of the front display completely. When “BRIGHT” or
“DIMMED1” is selected, the brightness level will be same as “DIMMED1” after the unit is
turned off. When “DIMMED2” or “OFF” is selected, the brightness level will be same as
“DIMMED2” after the unit is turned off.
8 POWER SAVE
OFF
ON
When this function is set to “ON”, you can reduce the power consumption
while the unit is turned off.
NOTES:
During Power Save mode —
— the front display panel will be turned off.
— the Just Clock function does not work.
Power Save does not work when —
— the unit is in the Timer mode.
— the unit’s power is turned off after timer-recording or Instant Timer Recording.
— the Satellite Auto Recording mode is engaged. (
pg. 71)
It takes some time for the unit to complete initialisation after you turn on unit power,
with “WAKE UP” blinking on the front display panel.
8 ON SCREEN LANGUAGE
This unit offers you the choice to view on-screen messages in 3 different
languages.
For details, refer to “On-screen Language Set” (
pg. 22).
DR-M10U_11Subsidiary.fm Page 99 Friday, March 5, 2004 11:54 AM
99

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JVC DRM10 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von JVC DRM10

JVC DRM10 Bedienungsanleitung - Deutsch - 116 seiten

JVC DRM10 Bedienungsanleitung - Holländisch - 116 seiten

JVC DRM10 Bedienungsanleitung - Französisch - 116 seiten

JVC DRM10 Bedienungsanleitung - Portugiesisch - 116 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info