Bedienungsanleitung JVC fs x3 (Seite 47 von 65) (Englisch)

158881

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

Basic Operations

English

Adjusting the Brightness

(DIMMER - at Power On)

You can adjust the brightness of the display.

When the System is Turned On

At power on, each time you press the DIMMER button on

the Remote Control, the brightness changes as follows:

DIMMER OFF = DIMMER 1 = DIMMER 2 = (back to

the beginning)

DIMMER OFF : Bright

DIMMER 1 : Dark (CD lamp also becomes dark.)

DIMMER 2 : Darker (CD lamp goes out.)

Power Saving Mode

(DIMMER - at Power Off)

In power saving mode, you can save the power while the

System is turned off (Standby Mode).

Each time you press the DIMMER button on the Remote

Control at power off, the display alternates as follows.

DISPLAY ON Ô DISPLAY OFF

To enable Power Saving mode, set to “DISPLAY

OFF”.

The display completely turns off to save the power.

To restore normal power mode,

reset to “DISPLAY ON”.

The Clock indicator

()

and the clock appear on the display.

Adjusting the Volume

Turn the VOLUME control on the Unit clockwise to in-

crease the volume or turn it counterclockwise to decrease

the volume.

Press the VOLUME + button on the Remote Control to in-

crease the volume or press the VOLUME

button on the

Remote Control to decrease the volume.

You can adjust the volume level between 0 and 50.

For private listening

Connect a pair of headphones to the PHONES jack. No

sound comes out of the speakers.

Be sure to turn down the volume before connecting or put-

ting on headphones.

CAUTION:

• DO NOT turn off the System with the volu-

me set to an extremely high level; otherwi-

se a sudden blast of sound could damage

your hearing, speakers and/or headphones

when you turn on the System or start play-

ing any source next time.

REMEMBER you cannot adjust the volume

level while the System is in standby mode.

Fade-out Muting (FADE MUTING)

You can mute the output with one touch operation.

To mute the output, press the FADE MUTING button

on the Remote Control. Then, “FADE MUTING” blinks

and the output will be faded out and becomes 0.

To release muting, press the FADE MUTING button once

again. Then, the output will be faded in to the original level.

• Adjusting the volume causes the muting process (fading

out to 0) to release.

• If you use the AHB PRO button or the BASS/TREBLE but-

ton during muting, the FADE MUTING button does not

work to release muting. In this case, turn the VOLUME

control on the Unit or the VOLUME+/

button on the Re-

mote Control to newly set the volume.

Reinforcing the Bass Sound

(Active Hyper Bass Pro.)

You can reinforce the bass sound to maintain rich, full bass at

low volume. (This effect does not apply to the headphones.)

To get the effect, press the AHB PRO button on the Unit

or the Remote Control.

“AHB PRO ON” appears and the “BASS” indicator lights up.

To cancel the effect, press the AHB PRO button again.

“AHB PRO OFF” appears and the “BASS” indicator goes out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC fs x3 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info