Bedienungsanleitung JVC fs x3 (Seite 50 von 65) (Englisch)

158881

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

Using the Tuner

English

Presetting Stations

You can preset up to 30 FM stations and up to 15 AM sta-

tions.

• Preset numbers may have been set to factory test fre-

quencies prior to shipment. This is not a malfunction. You

can preset the stations you want into memory by following

one of the presetting methods below.

On the Remote Control

Select a band by pressing the FM/AM

button.

Press the

∞

button to tune in a sta-

tion.

Press the SET button.

Preset number “1” will blink for 5 seconds.

Within 5 seconds, proceed to the next step.

When the display returns to the one set in step 2 after 5

seconds, press the SET button again.

Press the Numeric Keys, or the

button within 5 seconds to select the

preset number.

Press the SET button within 5 seconds.

“STORED” appears and after 2 seconds, the display re-

turns to the broadcast frequency display.

Repeat above steps 1 to 5 for each sta-

tion you want to store in memory with a

preset number.

To change the preset stations, repeat the same

steps as above.

CAUTION:

• Even if the system is unplugged or if the

power failure occurs, the preset stations

will be stored for about 24 hours. However,

in case the preset stations are erased, you

will need to preset the stations again.

To Change the FM Reception

Mode

When you are tuned into an FM stereo broadcast, the “ST.”

indicator lights up and you can hear stereo effects.

If an FM stereo broadcast is hard to receive or noisy, you

can select Monaural mode. Reception improves, but you

lose stereo effect.

FM AUTO mode is also useful to suppress static noise be-

tween stations.

To enter Monaural mode while receiving an FM

broadcast, press the FM/PLAY MODE button on the Re-

mote Control until “FM MONO” appears on the display. Then,

the “MONO” indicator lights up.

Each time you press the FM/PLAY MODE button, the display

alternates between “FM AUTO” and “FM MONO”.

To restore the stereo effect, press the FM/PLAY

MODE button on the Remote Control until “FM AUTO” ap-

pears on the display. Then, the “MONO” indicator goes out

and the “ST.” indicator will light up.

Beat Cut (AM Reception)

Switching the Beat Cut mode may reduce beat noise.

Each time you press the FM/PLAY MODE button while re-

ceiving an AM broadcast, the Beat Cut mode changes as fol-

lows.

BEAT CUT 1

BEAT CUT 2

BEAT CUT 3

BEAT CUT 4

(back to the beginning)

Set to the position where beat noise is small.

• The best position will differ depending on the AM

broadcast station being received.

• In AM broadcast, reception sensitivity will be changed by

turning the AM loop antenna. Turn the AM loop antenna

for best reception.

SET

+10

1 STORED

SET

When changing the Band

FM = 30, AM = 15

FM/PLAY

MODE

FM AUTO Ô FM MONO

FM/PLAY

MODE

Example:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC fs x3 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info