Bedienungsanleitung JVC FSSD1000R (Seite 14 von 28) (Englisch)

29829

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Using the Powered Subwoofer

Operating the Powered

Subwoofer

Presetting the Volume

You need to preset the volume level of this speaker (SP-

PW1000) to match those of the main speakers (SP-

FSSD1000). Once you preset the volume level, it is stored

as your reference level and the volume level of this speaker

will be able to automatically change as the volume level of

the Center Unit (CA-FSSD1000R) changes.

Press the POWER button of the Sub-

woofer to turn on the power.

The STANDBY/ON indicator of the Subwoofer will

light in

green

Set the VOLUME of the Subwoofer in the

“MIN” position.

Adjust the volume of the Center Unit to

your listening level.

Adjust the VOLUME of the Subwoofer to

balance the volume with the main

speakers.

To turn off the Subwoofwer,

press the POWER button

to light off the STANDBY/ON indicator.

Adding the Richness to the Bass (PHASE)

If you want to add the richness more to the bass, press the

PHASE button to set it either in the “

_ REVERSE” position

or the “

— NORMAL” position, whichever can add the rich-

ness to the bass.

Normally, the PHASE button should be set in the “— NOR-

MAL” position.

Automatic Operating Status On/Off

To save energy, the Subwoofer enters the Standby mode if

no (or very weak) sound signals come into the Subwoofer

for about 5 minutes. In Standby mode, the STANDBY/ON

indicator of the Subwoofer lights in red.

When sound signals come in again, the Subwoofer enters

the Operating mode and reproduces the sounds. The

STANDBY/ON indicator will light in green again.

CAUTION:

• Be sure to turn off the POWER of the Pow-

ered Subwoofer when the Powered Sub-

woofer is not in use for an extended period

of time.

INPUT Terminals

The Subwoofer has the following INPUT terminals.

INPUT(LOW-LEVEL):

Usually, the LEFT/MONO terminal is connected to the

SUBWOOFER terminal of the Center Unit with the sup-

plied signal cord. (see page 7)

VOLUME

PHASE

POWER

INPUT (LOW-LEVEL)

INPUT (HIGH-LEVEL)

STANDBY/ON

indicator

When the Center Unit CA-FSSD1000R

is not used (Using other equipment)

If an amplifier etc. to be connected does not have the

SUB WOOFER OUT terminals, the RIGHT and

LEFT/MONO terminals will be connected to the LINE

OUT-RIGHT and LEFT terminals of that unit.

INPUT (HIGH-LEVEL):

You can connect the speaker output terminals of other

amplifier etc. to these terminals.

Connect the speaker cords in parallel to the speaker ter-

minals on the amplifier etc.

• Do not use the INPUT (LOW-LEVEL) terminals and

the INPUT (HIGH-LEVEL) terminals at the same time.

LINE OUT

LEFTRIGHT

Connecting cord

(not supplied)

Amplifier etc.

SPEAKER

LEFTRIGHT

Amplifier

etc.

Speaker cords

(not supplied)

FS-SD1000R(B)E.book Page 11 Thursday, March 29, 2001 1:38 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC FSSD1000R Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC FSSD1000R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info