Bedienungsanleitung JVC GD-V4210PZW (Seite 11 von 40) (Englisch)

40062

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH

Precautions

• Before making connections, turn off all the equipment.

• Plugs should be firmly inserted; poor connection could cause noise.

• To unplug a cord, be sure to grasp its plug and pull it out.

• Connect the power cord after having finished all other connections.

• Refer also to the user manual of each piece of equipment.

Available Signals

Video signals

The following signals can be input to this Monitor:

• VIDEO A and VIDEO B terminals accept — PAL, NTSC, NTSC4.43, and SECAM signals.

• COMPONENT terminals accept — 480i, 576i, 480p, 720p, and 1080i (1035i) signals.

(For GD-V4210PCE, GD-V4210PCE-G, and GD-V4211PCE, to input the above signals, you need to install the video interface kit

(IF-C421P1W), which is separately purchased.)

Computer signals (Preset and user-defined video modes)

This Monitor has 13 preset video modes for the most popular industrial standard (marked with ¶ in the table below), and the

signals of the following image resolutions can be input to the RGB input terminals.

For less common video modes, this Monitor can also display a picture, and memorize the video modes as user-defined video

modes (up to five modes).

When a signal other than any of the preset modes is input, it will automatically be stored as a user-defined video mode, and

when a sixth user-defined video signal is input, the first mode will be erased from memory.

1 PC98 640 400 24.8 56.4 Non-interlace ¶

2 VGA400-70 640 400 31.5 70.1 Non-interlace ¶

3 VGA480-60 640 480 31.5 59.9 Non-interlace ¶

4 VGA480-72 640 480 37.9 72.8 Non-interlace ¶

5 VGA480-75 640 480 37.5 75.0 Non-interlace ¶

6 MAC13” 640 480 35.0 66.7 Non-interlace ¶

7 SVGA-56 800 600 35.2 56.3 Non-interlace ¶

8 SVGA-60 800 600 37.9 60.3 Non-interlace ¶

9 SVGA-72 800 600 48.1 72.2 Non-interlace ¶

10 XGA-60 1024 768 48.4 60.0 Non-interlace ¶

11 XGA-70 1024 768 56.5 70.1 Non-interlace ¶

12 RGB15K-60 — — 15.7 59.9 Interlace ¶

13 RGB15K-50 — — 15.6 50.0 Interlace ¶

– User-defined — — 15.0 – 16.0 50.0 – 75.0 Interlace

– User-defined — — 16.0 – 56.0 50.0 – 75.0 Non-interlace

Notes:

• When you are viewing XGA, setting the refresh rate (vertical scan frequency) of your personal computer to 60 Hz will enhance

the video image.

• When a signal other than listed above is input, a part of the screen may become void or an unnecessary picture may appear.

• Signals, though they are within the acceptable range of frequencies, may not be displayed normally, depending on the signal

type.

• Depending on the connected equipment, the Monitor may not be compatible with composite sync (Cs) or G on sync signals.

• When a preset mode signal is input, the vertical frequency displayed on the screen will have an “*” shown at its right top

position.

• When No. 7 to No. 11 signals are input, thin lines may happen to be hard to view on the screen, due to the internal digital

processing.

Connections

Screen resolution

Horizontal

Vertical

Horizontal

Frequency (kHz)

Vertical

Frequency (Hz)

Preset

setting

Signal name Scan systemNo.

04-13.GD-V4210PZW[EN]/f 00.9.29, 5:54 PM11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC GD-V4210PZW Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info