Bedienungsanleitung JVC GR-D200 (Seite 69 von 88) (Englisch)

23033

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENEN





$'

$'$'

Master Page: Right-Heading0

TROUBLESHOOTING

If, after following the steps in the chart below, the problem still exists, please consult your nearest JVC dealer.

Power

Video and D.S.C. Recording

The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio,

etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery

pack, AC Adapter, etc.) and wait a few minutes; and then re-connect it and proceed as usual from the

beginning.

SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION

1. No power is supplied. 1. •The power is not connected

properly.

•The battery is dead.

•The LCD monitor is not open

fully or the viewfinder is not

pulled out when recording.

1. • Connect the AC Adapter

securely. (੬ pg. 11)

•Replace the dead battery

with a fully charged one.

(੬ pg. 10, 11)

•Open the LCD monitor fully

or pull out the viewfinder.

SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION

2. Recording cannot be

performed.

2. •The Power Switch is set to

“PLAY” or “OFF”.

— For Video Recording —

•The tape’s erase protection

tab is set to “SAVE”.

•The VIDEO/MEMORY

Switch is set to “MEMORY”.

•“TAPE END” appears.

•The cassette holder cover is

open.

— For D.S.C. Recording —

•The VIDEO/MEMORY

Switch is set to “VIDEO”.

2. • Set the Power Switch to “A”

or “M”. (੬ pg. 17, 23)

— For Video Recording —

•Set the tape’s erase

protection tab to “REC”.

(੬ pg. 15)

•Set the VIDEO/MEMORY

Switch to “VIDEO”.

•Replace with new cassette.

(੬ pg. 15)

•Close the cassette holder

cover.

— For D.S.C. Recording —

•Set the VIDEO/MEMORY

Switch to “MEMORY”.

3. When shooting a subject

illuminated by bright light,

vertical lines appear.

3. •This is a result of exceedingly

high contrast, and is not a

malfunction.

—

4. When the screen is under

direct sunlight during shooting,

the screen becomes red or

black for an instant.

4. •This is not a malfunction. 4.

—

5. During recording, the date/

time does not appear.

5. •“DATE/TIME” is set to “OFF”. 5. •Set “DATE/TIME” to “ON”.

(੬ pg. 31, 38)

6. During recording, sound

cannot be heard.

6. •The is normal. 6.

—

7. The LCD monitor or

viewfinder indications blink.

7. •Certain Wipe/Fader effects,

certain modes of Program AE

with special effects, “DIS”

and other functions that

cannot be used together are

selected at the same time.

7. • Re-read the sections covering

Wipe/Fader effects, Program

AE with special effects and

“DIS”. (੬ pg. 31 – 34, 36)

CONTINUED ON NEXT PAGE

REFERENCES

GR-D200US.book Page 69 Friday, April 11, 2003 1:05 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC GR-D200 Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC GR-D200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info