Bedienungsanleitung JVC GR-D22 (Seite 13 von 40) (Englisch)

663428

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

TAPE RECORDING

Time Code

During recording, a time code is recorded on the tape.

This code is to confirm the location of the recorded

scene on the tape during playback.

If recording starts from a blank portion, the time code

begins counting from “00:00:00” (minute:second:frame).

If recording starts from the end of a previously recorded

scene, the time code continues from the last time code

number.

If during recording a blank portion is left partway

through the tape, the time code is interrupted. When

recording is resumed, the time code starts counting up

again from “00:00:00”. This means the camcorder may

record the same time codes as those existing in a

previously recorded scene. To prevent this, perform

“RECORDING FROM THE MIDDLE OF A TAPE” in the

following cases;

• When shooting again after playing back a recorded

tape.

• When power shuts off during shooting.

• When a tape is removed and re-inserted during

shooting.

• When shooting using a partially recorded tape.

• When shooting on a blank portion located partway

through the tape.

• When shooting again after shooting a scene then

opening/closing the cassette holder cover.

Display

RECORDING FROM THE MIDDLE OF A TAPE

1 Play back a tape or use Blank Search (墌 pg. 14) to

find the spot at which you want to start recording, then

engage the Still Playback mode (墌 pg. 13, “Normal

Playback”).

2 Set the Power Switch r to “ ” or “ ” while

pressing down the Lock Button e located on the

switch, then start recording.

NOTES:

● The time code cannot be reset.

● During fast-forwarding and rewinding, the time code

indication does not move smoothly.

● The time code is displayed only when “TIME CODE” is

set to “ON” (墌 pg. 24).

Frames

(30 frames = 1 second)

Seconds

Minutes

Frames are not displayed

during recording.

Normal Playback

1 Load a tape (墌 pg. 9).

2 Set the Power Switch r to “PLAY” while pressing

down the Lock Button e located on the switch. To start

playback, press

• To stop playback temporarily (Still Playback), press

• To stop playback, press 7 4.

• Press 1 5 to rewind, or ¡ 7 to fast-forward the

tape during Stop mode.

• High-speed picture search (Shuttle Search) is

possible by pressing 1 5 or ¡ 7 during playback

(holding 1 5 or ¡ 7 down during playback

continues search until released).

• At any time, pressing

6 resumes normal

playback.

To Control The Speaker Volume:

Rotate the MENU/VOLUME wheel # so that the

volume level indicator i on the display moves to

obtain the appropriate volume.

ATTENTION

During Shuttle Search, parts

of the picture may not be

clearly visible, particularly on

the left side of the screen.

TAPE PLAYBACK

12:34 :24

Speaker

Continued on next page.

GR-D22_11-15_EN 25/9/03, 3:28 PM13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC GR-D22 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC GR-D22

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info