Bedienungsanleitung JVC GR-D24 (Seite 30 von 40) (Englisch)

7393

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

TROUBLESHOOTING

30 EN

MasterPage: Left

● The DV cable was plugged/unplugged with power turned

on.

HTurn the camcorder’s power off and on again, then operate

it.

● The light used to illuminate the LCD monitor causes it to

become hot.

HClose the LCD monitor to turn it off or set the Power Switch

to “OFF”, and let the unit cool down.

● In places subject to low temperature, images become dark

due to the characteristics of the LCD monitor. When this

happens, the displayed colours differ from those that are

actually recorded. This is not a defect of the camcorder.

HAdjust the brightness and angle of the LCD monitor.

(੬ pg. 9, 10)

● When the LCD monitor’s fluorescent light reaches the end

of its service life, images on the LCD monitor become dark.

HConsult your nearest JVC dealer.

● The LCD monitor and the viewfinder are made with high-

precision technology. However, black spots or bright spots

of light (red, green or blue) may appear constantly on the

LCD monitor or the viewfinder during recording or

playback. These spots are not recorded on the tape. This is

not due to any defect of the unit. (Effective dots: more than

99.99 %)

● This may occur when the surface or the edge of the LCD

monitor is pressed.

● The battery’s charge is low.

HInstall a fully charged battery. (੬ pg. 6, 7)

● The viewfinder is pulled out and “PRIORITY” is set to

“FINDER”.

HPush the viewfinder back in or set “PRIORITY” to “LCD”.

(੬ pg. 10, 14, 16)

● The LCD monitor’s brightness setting is too dark.

HAdjust the brightness of the LCD monitor. (੬ pg. 9)

HIf the monitor is tilted upward 180 degrees, open the

monitor fully. (੬ pg. 10)

● The speaker volume is too great.

HTurn the speaker volume down. (੬ pg. 12)

HWipe them gently with soft cloth. Wiping strongly can

cause damage. (੬ pg. 34) To clean the viewfinder, please

consult your nearest JVC dealer.

● “TIME CODE” is set to “OFF”.

HSet “TIME CODE” to “ON”. (੬ pg. 14, 16, 17)

● A malfunction of some kind has occurred. In this case the

camcorder’s functions become unusable.

H੬ pg. 31.

● A malfunction of some kind has occurred. In this case the

camcorder’s functions become unusable.

H੬ pg. 31.

When the camcorder is connected via the DV

connector, the camcorder does not operate.

The rear of the LCD monitor is hot.

Images on the LCD monitor appear dark or whitish.

Coloured bright spots appear all over the LCD

monitor or the viewfinder.

The indicators and the image colour on the LCD

monitor are not clear.

The cassette will not load properly.

Picture does not appear on the LCD monitor.

Images on the LCD monitor are jittery.

The LCD monitor, the viewfinder and the lens have

become dirty (ex. fingerprints).

Time code does not appear.

An error indication (E01, E02 or E06) appears.

An error indication (E03 or E04) appears.

GR-D33EK.book Page 30 Thursday, October 30, 2003 9:41 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC GR-D24 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC GR-D24

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info