Bedienungsanleitung JVC GR-D31 (Seite 32 von 48) (Englisch)

533229

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

USING THE REMOTE CONTROL UNIT

DIAGNOSING VCR/CAMCORDER TIMING

1 Play back the tape in the camcorder, then point the

remote control at the camcorder’s remote sensor and

press R.A.EDIT ON/OFF r.

The Random Assemble Editing Menu appears.

2 Perform Random Assemble Editing on Programme 1

only. In order to check VCR and camcorder timing,

select the beginning of a scene transition as your Edit-

In point.

3 Play back the dubbed scene.

• If any images from the scene prior to the transition

you chose for your Edit-In point were recorded, that

means your VCR moves too quickly from Record-

Pause to Record mode.

• If the scene you tried to dub starts in progress, the

VCR is slow to start recording.

ADJUSTMENT OF VCR/CAMCORDER TIMING

4 Point the remote control at the camcorder’s remote

sensor and press R.A.EDIT ON/OFF r to make the

Random Assemble Editing menu disappear, then press

the MENU/VOLUME wheel $ in. The Menu Screen

appears.

5 Rotate the MENU/VOLUME wheel $ to select

“ VIDEO” and press it. Then, rotate it to

“SYNCHRO” and press it. The value for “SYNCHRO” is

highlighted.

6 Based on the diagnostics performed, you can now

advance the VCR’s record timing by rotating the

MENU/VOLUME wheel $ towards “+”. You can also

delay the VCR’s record timing by rotating the MENU/

VOLUME wheel $ towards “–”. The adjustment range

is from –1.3 to +1.3 seconds, in 0.1-second incre-

ments. Press the MENU/VOLUME wheel $ in to finish

the setting.

7 Rotate the MENU/VOLUME wheel $ to select

“ RETURN” and press it twice.

Now perform Random Assemble Editing beginning with

step 4 on page 31.

NOTES:

● Before performing actual Random Assemble Editing, do a

few Random Assemble Editing trial runs to check whether

the value you have input is appropriate or not, and make

adjustments accordingly.

● Depending on the recorder, there may be situations

where the timing difference cannot be fully corrected.

AUTOMATIC EDITING TO VCR

Rewind the tape in the camcorder to the beginning

of the scene you want to edit and press PAUSE (6) e.

Point the remote control towards the VCR’s

remote sensor and press VCR REC STBY (q6) t, or

manually engage the VCR’s Record-Pause mode.

Press the Recording Start/Stop Button w on the

camcorder. Editing proceeds as programmed, right

through to the end of the last registered scene.

• When dubbing is complete, the camcorder enters the

Pause mode, and the VCR enters its Record-Pause

mode.

• If you do not register an Edit-Out point, the tape will

be dubbed all the way to the end automatically.

• If you operate the camcorder during automatic editing,

the VCR will enter its Record-Pause mode and

automatic editing will stop.

Engage the Stop modes for the camcorder and the

VCR.

To make the R.A.Edit counter display disappear, press

R.A.EDIT ON/OFF r on the remote control.

NOTES:

● Pressing R.A.EDIT ON/OFF r on the remote control

clears all settings registered during Random Assemble

Editing.

● When the editing cable is connected to the remote

control’s Pause In connector during dubbing, make sure

the remote control is pointed at the VCR’s sensor, and

the path between the two is unobstructed.

● Random Assemble Editing may not function properly

when using a tape including several duplicated time

codes (

੬ pg. 13).

For More Accurate Editing

Some VCRs make the transition from Record-Pause to

Record mode faster than others. Even if you begin

editing for the camcorder and the VCR at exactly the

same time, you may lose scenes you wanted, or find

that you have recorded scenes you did not want. For a

cleanly edited tape, confirm and adjust the timing of the

camcorder against your VCR.

● If you select Sepia or Monotone mode from Programme

AE with special effects, you cannot use the Black & White

Fader. In this case the Black & White indicator begins

blinking. Once the next Edit-In point is registered, the

effect is turned off. To combine these effects, use Sepia

or Monotone during recording, then use the Black &

White Fader during Random Assemble Editing.

● It is not possible to use Fade/Wipe effects and

Programme AE with special effects during Random

Assemble Editing using a DV cable.

GR-D31/21EK 28-33 02.12.19, 9:15 PM32

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC GR-D31 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info