Bedienungsanleitung JVC GR-D40 (Seite 13 von 48) (Englisch)

533227

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

TAPE RECORDING

Time Code

During recording, a time code is recorded on the tape.

This code is to confirm the location of the recorded

scene on the tape during playback.

If recording starts from a blank portion, the time code

begins counting from “00:00:00” (minute:second:frame).

If recording starts from the end of a previously recorded

scene, the time code continues from the last time code

number.

To perform Random Assemble Editing (੬ pg. 30 – 32),

time code is necessary. If during recording a blank

portion is left partway through the tape, the time code

is interrupted. When recording is resumed, the time

code starts counting up again from “00:00:00”. This

means the camcorder may record the same time codes

as those existing in a previously recorded scene. To

prevent this, perform “RECORDING FROM THE

MIDDLE OF A TAPE” in the following cases;

• When shooting again after playing back a recorded

tape.

• When power shuts off during shooting.

• When a tape is removed and re-inserted during

shooting.

• When shooting using a partially recorded tape.

• When shooting on a blank portion located partway

through the tape.

• When shooting again after shooting a scene then

opening/closing the cassette holder cover.

Display

RECORDING FROM THE MIDDLE OF A TAPE

1 Play back a tape or use Blank Search (੬ pg. 14) to

find the spot at which you want to start recording, then

engage the Still Playback mode (੬ pg. 13, “Normal

Playback”).

2 Set the Power Switch y to “ ” or “ ” while

pressing down the Lock Button t located on the

switch, then start recording.

NOTES:

● The time code cannot be reset.

● During fast-forwarding and rewinding, the time code

indication does not move smoothly.

● The time code is displayed only when “TIME CODE” is

set to “ON” (

੬ pg. 24).

Frames

(25 frames = 1 second)

Seconds

Minutes

Frames are not displayed

during recording.

Normal Playback

1 Load a tape (੬ pg. 9).

2 Set the Power Switch y to “PLAY” while pressing

down the Lock Button t located on the switch. To start

playback, press

/6 6.

• To stop playback temporarily (Still Playback), press

/6 6.

• To stop playback, press 5 4.

• Press

5 to rewind, or

7 to fast-forward the

tape during Stop mode.

• High-speed picture search (Shuttle Search) is

possible by pressing

5 or

7 during playback

(holding

5 or

7 down during playback

continues search until released).

• Press the Zoom Button T l on the remote control to

zoom in (up to 44X), or W ; to zoom out. You can

also magnify a particular part of an image (੬ pg. 28).

• At any time, pressing

/6 6 resumes normal

playback.

Slow-Motion Playback/Playback Special Effects/

Playback Zoom:

Available only with the remote control (੬ pg. 28)

To Control The Speaker Volume:

Rotate the MENU/VOLUME wheel $ so that the

volume level indicator o on the display moves to obtain

the appropriate volume.

ATTENTION

During Shuttle Search, parts

of the picture may not be

clearly visible, particularly on

the left side of the screen.

TAPE PLAYBACK

12:34:24

Speaker

Continued on next page.

01 D50/40/30/20EK 11-15 02.12.4, 19:0913

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC GR-D40 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC GR-D40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info