Bedienungsanleitung JVC GR-D93 (Seite 39 von 56) (Englisch)

56733

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

REFERENCES

EN 39

MasterPage: Ref_Heading0_Right

ADDITIONAL INFORMATION

Power (pg. 6)

● Perform charging where the temperature is between 10°C

and 35°C. 20°C to 25°C is the ideal temperature range for

charging. If the environment is too cold, charging may be

incomplete.

● Charging time is based on room temperature of 20°C.

● Charging times are for a fully discharged battery pack.

● Charging time varies according to the ambient temperature

and the status of the battery pack.

● To avoid interference with reception, do not use the AC

Adapter near a radio.

● Since the AC Adapter processes electricity internally, it

becomes warm during use. Be sure to use it only in well-

ventilated areas.

● The following operation stops charging:

• Set the Power Switch to “PLAY”, “A” or “M”.

• Disconnect the AC Adapter from the camcorder.

• Unplug the AC Adapter from the AC outlet.

• Detach the battery from the camcorder.

● Using the optional AA-V40 AC Power Adapter/Charger, you

can charge the BN-V408U/V416U/V428U battery pack

without the camcorder. However, it cannot be used as an

AC Adapter.

Loading/Unloading A Cassette (pg. 10)

● It takes a few seconds for the cassette holder to open. Do

not apply force.

● If you wait a few seconds and the cassette holder does not

open, close the cassette holder cover and try again. If the

cassette holder still does not open, turn the camcorder off

then on again.

● If the tape does not load properly, open the cassette holder

cover fully and remove the cassette. A few minutes later,

insert it again.

● When the camcorder is suddenly moved from a cold place

to a warm environment, wait a short time before opening

the cassette holder cover.

● Closing the cassette holder cover before the cassette

holder recedes may cause damage to the camcorder.

● Even when the camcorder is switched off, a cassette can

be loaded or unloaded. After the cassette holder is closed

with the camcorder switched off, however, it may not

recede. It is recommended to turn the power on before

loading or unloading.

● When resuming recording, once you open the cassette

holder cover a blank portion will be recorded on the tape or

a previously recorded scene will be erased (recorded over)

regardless of whether the cassette holder came out or not.

See “Recording From The Middle Of A Tape” (੬ pg. 13).

VIDEO RECORDING (pg. 11)

● When you use the LCD monitor outdoors in direct sunlight,

the LCD monitor may be difficult to see. If this happens, use

the viewfinder instead.

● The cassette holder cannot be opened unless a power

supply is attached.

● There may be a delay after you open the cassette holder

cover until the cassette holder opens. Do not use force.

● Once the cassette holder is closed, it recedes

automatically. Wait until it recedes completely before

closing the cassette holder cover.

● When the Recording Start/Stop button is pressed, it may

take a few seconds before actual recording starts. The “T”

indicator starts rotating when the camcorder actually starts

recording.

● The time required to calculate and display the remaining

tape length, and the accuracy of the calculation, may vary

according to the type of tape used.

● “TAPE END” appears when the tape reaches its end, and

the power goes off automatically if left in this condition for 5

minutes. “TAPE END” also appears when a cassette at its

end is loaded.

VIDEO PLAYBACK (pg. 14)

● Clean the video heads using an optional dry cleaning

cassette when:

• No picture during playback.

• Blocks of noise appear during playback.

For details, ੬ pg. 46.

● If Stop mode continues for 5 minutes when power is

supplied from a battery, the camcorder shuts off

automatically. To turn on again, set the Power Switch to

“OFF”, then to “PLAY”.

● You can also view the playback picture on the LCD monitor

with it flipped over and pushed against the camcorder body.

● LCD monitor/viewfinder indications:

• When power is supplied from a battery: the “ ”

battery indicator is displayed. (੬ pg. 43)

• When power is supplied from an AC outlet: the “ ”

battery indicator does not appear.

● When a cable is connected to the AV connector, the sound

is not heard from the speaker.

D.S.C. RECORDING (GR-D93/D73 only) (pg. 18)

● Even if “DIS” is set to “ON” (੬ pg. 25), the Stabiliser will be

disabled.

● If Program AE with special effects (੬ pg. 30) is engaged,

certain modes of Program AE with special effects are

disabled during Snapshot recording. In such a case, the

icon blinks.

● If shooting is not performed for approx. 5 minutes when the

Power Switch is set to “A” or “M” and power is supplied

from the battery pack, the camcorder shuts off

automatically to save power. To perform shooting again,

push back and pull out the viewfinder again or close and re-

open the LCD monitor.

● The Motor Drive mode (੬ pg. 31) is disabled when the

VIDEO/MEMORY Switch is set to “MEMORY”.

● When a cable is connected to the AV connector, the shutter

sound is not heard from the speaker.

● Still images taken are compliant to DCF (Design rule for

Camera File system). They do not have any compatibility

with devices which are not compliant to DCF.

REFERENCES

GR-D93PAL.book Page 39 Wednesday, October 29, 2003 9:36 AM

JVC GR-D93 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC GR-D93

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info