Bedienungsanleitung JVC GR-DVL317 (Seite 53 von 92) (Englisch)

595799

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

EN53

PLAY (

)

STOP (5)

Dubbing To Or From A Video Unit Equipped

With A DV Connector (Digital Dubbing)

It is also possible to copy recorded scenes from the

camcorder onto another video unit equipped with a DV

connector. Since a digital signal is sent, there is little if any

image or sound deterioration.

[To use this camcorder as a player]

Make sure all units are turned off. Connect the

camcorder to a video unit equipped with a DV input

connector using a DV cable as shown in the illustration.

Set the VIDEO/DSC Switch to “VIDEO” (GR-DVL817

only), set the camcorder’s Power Switch to “ ”

while pressing down the Lock Button located on the

switch, turn on the video unit’s power, and insert the

appropriate cassettes in the camcorder and the video

unit.

Press

to play back the source tape.

While watching the playback on the monitor, engage

the DV connector-equipped video unit’s record mode

from the spot on the source tape you want to begin

recording.

NOTES:

●

It is recommended to use the AC Adapter as the power supply

instead of the battery pack (

墌

pg. 9).

●

If the remote control is used when both the player and

recorder are JVC video units, both units will perform the

same operation. To prevent this from happening, press the

buttons on both units.

●

If a blank portion or disturbed image is played back on the

player during dubbing, the dubbing may stop so that an

unusual image is not dubbed.

●

Even though the DV cable is connected correctly, some-

times the image may not appear in step 4. If this occurs, turn

off the power and make connections again.

●

If “Playback Zoom” (

墌

pg. 60), “Playback Special Effects”

(GR-DVL817 only,

墌

pg. 59) or “Snapshot” is attempted

during playback, only the original playback image recorded

on the tape is output from the DV IN/OUT connector.

●

When using a DV cable, be sure to use the optional JVC

VC-VDV204U DV cable.

DV cable

(optional)

To Use This Camcorder As A Recorder . . .

1. Set the VIDEO/DSC Switch to “VIDEO” (GR-DVL817 only), then turn the Power Switch to “ ” while

pressing down the Lock Button located on the switch.

2. Set “REC MODE” to “SP” or “LP” in the Menu Screen (墌 pg. 50)

3. Connect the DV cable as shown in the illustration and load a cassette to record on.

4. Press the Recording Start/Stop button to engage the Record-Pause mode. “

DV. IN

” appears on the screen.

5. Press the Recording Start/Stop button to start recording. rotates.

6. Press the Recording Start/Stop button again to engage the Record-Pause mode. stops rotating.

NOTES:

●

Digital Dubbing is performed in the sound mode recorded on the original tape, regardless of the current

“SOUND MODE” setting (

墌

pg. 47).

●

During Digital Dubbing, no signals are output from the video or audio connectors.

Video unit equipped

with DV connector

To DV

IN/OUT

To DV

IN/OUT

Power Switch

Core filter

VIDEO/DSC Switch

(GR-DVL817 only)

Lock Button

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC GR-DVL317 Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info