Bedienungsanleitung JVC GR-DVP8 (Seite 57 von 84) (Englisch)

533257

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

EN 57

Master Page: Right

1 Load the provided memory card. (੬ pg. 16)

Then, perform step 1 and 2 of “Audio Dubbing”

(੬ pg. 56).

2 Press MENU. The Menu Screen appears.

3 Press + or – to select “s”, and press SET/

SELECT. The SYSTEM Menu appears.

4 Press + or – to select “SOUND IN”, and press

SET/SELECT. The Sub Menu appears.

5 Press + or – to select “D.SOUND”, and press

SET/SELECT.

6 Press + or – to select “BRETURN”, and press SET/

SELECT twice. The Menu Screen closes and the

sound effect indication appears.

7 Press INDEX to access the sound effects Index

Screen.

8 Press + or – to select the desired sound effect and

press SET/SELECT.

9 Press PLAY (U) to begin Audio Dubbing. The

selected sound effect is dubbed onto the tape.

● The “ ” moves while it is being dubbed.

● To stop dubbing the sound effect midway, press

D.SOUND.

10 Press STOP (8) to end Audio Dubbing.

NOTES:

● After dubbing, set “SOUND IN” back to “MIC/

AUX”.

● The dubbed sound effect is recorded on

SOUND 2. (੬ pg. 40)

● If you press PAUSE (9) to pause dubbing in step 9

the selected sound effect indication remains

displayed. To resume dubbing, press PLAY (U).

You can record a new scene into a previously

recorded tape, replacing a section of the original

recording with minimal picture distortion at the in

and outpoints. The original audio remains

unchanged.

NOTES:

● Before performing the following steps, make sure

that “TIME CODE” is set to “ON”. (੬ pg. 31, 41)

● Insert Editing is not possible on a tape recorded in

the LP mode or on a blank portion of a tape.

● To perform Insert Editing while watching in the

television, make connections. (੬ pg. 22)

1 Play back the tape, locate the Edit-Out point and

press PAUSE (9). Confirm the time code at this

point. (੬ pg. 41)

2 Press REW (

) until the Edit-In point is located,

then press PAUSE (9).

3 Press and hold INSERT (I) on the remote

control, then press PAUSE (9). The “9I”

indicator and the Time Code (min.:sec.) appear

and the camcorder enters Insert-Pause mode.

4 Press START/STOP to begin editing.

● Confirm the insert at the time code you

checked in step 1.

● To pause editing, press START/STOP. Press it

again to resume editing.

5 To end Insert Editing, press START/STOP, then

STOP (8).

NOTES:

● Program AE with special effects (੬ pg. 33) can be

used to spice up the scenes being edited during

Insert Editing.

● During Insert Editing, the date and time

information changes.

● If you perform Insert Editing onto a blank space on

the tape, the audio and video may be disrupted.

Make sure you only edit recorded areas.

● During Insert Editing, when the tape moves to

scenes recorded in the LP mode or a blank

portion, Insert Edting stops. (੬ pg. 80, 81)

● If a memory card is loaded and “NAVIGATION” is

set to other than “MANUAL”, a NAVIGATION

thumbnail image is stored in the memory card.

(੬ pg. 47)

Insert Editing

PAUSE

START/STOP

INSERT

PLAY

REW

STOP

ADVANCED FEATURES

GR-DVP9-8PAL.book Page 57 Friday, February 7, 2003 12:35 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC GR-DVP8 Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info