Bedienungsanleitung JVC GR-DX300 (Seite 12 von 60) (Englisch)

39846

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

1h30m

1h29m

0h03m

1h30m

0h02m

0h01m

0h00m

180°

90°

During shooting

Basic Recording

Perform the procedures listed below before continuing.

● Power (੬ pg. 7)

● Grip Adjustment (੬ pg. 8)

● Viewfinder Adjustment (੬ pg. 8)

● Load A Cassette (੬ pg. 9)

● Recording Mode Setting (੬ pg. 10)

1 Remove the lens cap.

Pull on bottom end Q of LCD monitor to open and set

the VIDEO/MEMORY Switch t to “VIDEO”.

2 Set the Power Switch @ to “ ” or “ ” while

pressing down the Lock Button $ located on the

switch.

Shooting while using the LCD monitor: Open the

LCD monitor fully.

Shooting while using the viewfinder: Pull out the

viewfinder fully.

• The Power lamp 0 lights and the camcorder enters

the Record-Standby mode. “PAUSE” 8 is displayed.

• The image will not appear simultaneously on the LCD

monitor and the viewfinder. See “PRIORITY” in the

SYSTEM Menu (੬ pg. 34).

3 Press the Recording Start/Stop Button !. “ ”

4, 8 appears and the tally lamp ^ lights while

recording is in progress.

• To Stop Recording, press the Recording Start/Stop

Button !. The camcorder re-enters the Record-

Standby mode.

To Adjust The Brightness Of The Display

..... press MONITOR BRIGHT + or – 5 until the bright

level indicator o on the display moves and the

appropriate brightness is reached.

• It is also possible to adjust the brightness of the

viewfinder. Pull out the viewfinder, set “PRIORITY” in

the SYSTEM Menu to “FINDER” (੬ pg. 34) and

adjust as described above.

TAPE RECORDING

NOTES:

● If the Record-Standby mode continues for 5 minutes, the

camcorder’s power shuts off automatically. To turn the

camcorder on again, push back and pull out the

viewfinder again or close and re-open the LCD monitor.

● When a blank portion is left between recorded scenes on

the tape, the time code is interrupted and errors may

occur when editing the tape. To avoid this, refer to

“RECORDING FROM THE MIDDLE OF A TAPE”

(

੬ pg. 14).

● To turn the tally lamp

^ or beep sounds off,

੬ pg. 34.

● When you use the LCD monitor outdoors in direct

sunlight, the LCD monitor may be difficult to see. If this

happens, use the viewfinder instead.

● Black spots or bright spots of light (red, green or blue)

may appear constantly on the LCD monitor or the

viewfinder (

੬ pg. 47).

● When the Recording Start/Stop button ! is pressed, it

may take a few seconds before actual recording starts.

“

” 4 starts rotating when the camcorder actually

starts recording.

● The time required to calculate and display the remaining

tape length, and the accuracy of the calculation, may vary

according to the type of tape used.

● “TAPE END” appears when the tape reaches its end, and

the power goes off automatically if left in this condition for

5 minutes. “TAPE END” also appears when a cassette at

its end is loaded.

Tape remaining time

indicator (Approximate)

Display

(Now calculating)

(Blinking)

01 DX300/100/95/75EK_EN 12-16 2/26/03, 7:12 PM12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC GR-DX300 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC GR-DX300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info