Bedienungsanleitung JVC GR-DX95 (Seite 38 von 60) (Englisch)

39850

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

DUBBING

Dubbing To Or From A Video Unit

Equipped With A DV Connector

(Digital Dubbing)

It is also possible to copy recorded scenes from this

camcorder onto another video unit equipped with a DV

connector. Since a digital signal is sent, there is little if

any image or sound deterioration.

To Use This Camcorder As A Player

1 Make sure all units are turned off. Connect this

camcorder to a video unit equipped with a DV input

connector using a DV cable as shown in the illustration.

2 Set this camcorder’s VIDEO/MEMORY Switch t to

“VIDEO”, then the Power Switch @ to “ ” while

pressing down the Lock Button $ located on the

switch, turn on the video unit’s power, and insert the

appropriate cassettes in this camcorder and the video

unit.

3 Press

! to play back the source tape.

4 While watching the playback on the monitor, engage

the DV connector-equipped video unit’s record mode

from the spot on the source tape you want to begin

recording.

NOTES:

● It is recommended to use the AC Adapter as the

power supply instead of the battery pack (

੬ pg. 7).

● If the remote control is used when both the player and

recorder are JVC video units, both units will perform the

same operation. To prevent this from happening, press

the buttons on both units.

● If a blank portion or disturbed image is played back on

the player during dubbing, the dubbing may stop so that

an unusual image is not dubbed.

● Even though the DV cable is connected correctly,

sometimes the image may not appear in step 4. If this

occurs, turn off the power and make connections again.

● If “Playback Zoom” (

੬ pg. 13, 39), “Playback Special

Effects” (੬ pg. 39) or “Snapshot” is attempted during

playback, only the original playback image recorded on

the tape is output from the DV connector

● When using a DV cable, be sure to use the optional

JVC VC-VDV204U DV cable.

To Use This Camcorder As A Recorder

1. Set this camcorder’s VIDEO/MEMORY Switch t to

“VIDEO”, then the Power Switch @ to “ ” while

pressing down the Lock Button $ located on the

switch.

2. Set “REC MODE” to “SP” or “LP” in the Menu

Screen (੬ pg. 35).

3. Connect the DV cable as shown in the illustration

and load a cassette to record on.

4. Press START/STOP k on the remote control to

engage the Record-Pause mode. “

DV. IN

” appears

on the screen.

DV cable

(optional)

Video unit equipped

with DV connector

To DV IN/OUT

To DV

)

Core filter

5. Press START/STOP k on the remote control to

start recording. 4 rotates.

6. Press START/STOP k on the remote control

again to engage the Record-Pause mode. 4

stops rotating.

NOTES:

● Digital Dubbing is performed in the sound mode recorded

on the original tape, regardless of the current “SOUND

MODE” setting (

੬ pg. 32).

● During Digital Dubbing, incoming signals cannot be

output through the video or audio connectors if they are

copy-guarded.

01 DX300/100/95/75EK_EN 35-44 2/26/03, 7:13 PM38

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC GR-DX95 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC GR-DX95

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info