Bedienungsanleitung JVC GR-DX97 (Seite 17 von 52) (Englisch)

39830

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

EN 17

MasterPage: Advan_Heading0_Right

VIDEO RECORDING & PLAYBACK

Time Code

During recording, a time code is recorded on the tape.

This code is to confirm the location of the recorded scene

on the tape during playback.

* Frames are not displayed during recording.

If recording starts from a blank portion, the time code

begins counting from “00:00:00” (minute:second:frame).

If recording starts from the end of a previously recorded

scene, the time code continues from the last time code

number.

To perform Random Assemble Editing (੬ pg. 41 – 44),

time code is necessary. If during recording a blank

portion is left partway through the tape, the time code is

interrupted. When recording is resumed, the time code

starts counting up again from “00:00:00”. This means the

camcorder may record the same time codes as those

existing in a previously recorded scene. To prevent this,

perform “Recording From The Middle Of A Tape” (see

below) in the following cases;

● When shooting again after playing back a recorded tape.

● When power shuts off during shooting.

● When a tape is removed and re-inserted during shooting.

● When shooting using a partially recorded tape.

● When shooting on a blank portion located partway through

the tape.

● When shooting again after shooting a scene then opening/

closing the cassette holder cover.

NOTES:

● The time code cannot be reset.

● During fast-forwarding and rewinding, the time code

indication does not move smoothly.

● The time code is displayed only when “TIME CODE” is set

to “ON”. (੬ pg. 30)

Recording From The Middle Of A Tape

1) Play back a tape or use Blank Search (੬ pg. 18) to

find the spot at which you want to start recording, then

engage the Still Playback mode. (੬ pg. 17)

2) Set the Power Switch to “A” or “M” while pressing

down the Lock Button located on the switch, then start

recording.

12:34:24

Minutes

Seconds

Frames*

(25 frames = 1 second)

Display

VIDEO PLAYBACK

1 Load a cassette. (੬ pg. 14)

2 Set the VIDEO/MEMORY Switch to “VIDEO”.

(GR-DX97/77/67only)

3 Set the Power Switch to “PLAY” while pressing down

the Lock Button located on the switch.

4 To start playback, press 4/9.

5 To stop playback, press 8.

● During Stop mode, press 3 to rewind, or 5 to fast-

forward the tape.

To control the speaker volume

Press VOL. + to turn up the volume, or VOL. – to turn

down the volume.

NOTES:

● The playback picture can be viewed in the LCD monitor,

viewfinder or on a connected TV. (੬ pg. 18)

● If Stop mode continues for 5 minutes when power is

supplied from a battery, the camcorder shuts off

automatically. To turn on again, set the Power Switch to

“OFF”, then to “PLAY”.

● When a cable is connected to the AV connector, the sound

is not heard from the speaker.

Still Playback

Pauses during video playback.

1) Press 4/9 during playback.

2) To resume normal playback, press 4/9 again.

● If still playback continues for more than about 3 minutes,

the camcorder’s Stop mode is automatically engaged.

Normal Playback

Speaker

4/9

Lock Button

VIDEO/MEMORY

(GR-DX97/77/

67only)

Power Switch

VOL. +/-

GR-DX97PAL.book Page 17 Tuesday, January 6, 2004 12:44 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC GR-DX97 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC GR-DX97

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info