34423
57
Zoom out
Zoom in
Vorherige Seite
1/96
Nächste Seite
57
9. TIME CODE OPERATION
TC GENERATOR
FREE
REC
PRESET
REGEN
CH-1
CH-2CH-1
CH-2
CH-1 CH-2
CONTINUE MENU
PRESETADVANCESHIFTHOLD
AUTO
MANUAL
FRONT
REAR
DATA SET
SELECTITEMGROUP
AUDIO SELECT
AUDIO INPUT
AUDIO
LEVEL
LITHIUM BATT.
4.
SHIFT button
6.
PRESET
button
3.
ADVANCE
button
2.
HOLD button
H M S F
HOLD
H M S F
HOLD
H M S F
HOLD
H M S F
HOLD
TIME CODE PRESETTING PROCEDURE
1.
Display the time code on the counter display.
Set the COUNTER switch to "TC".
Time code up to 23 hrs. 59 min. 59 sec. 29 frames can be
preset.
2.
Place the time code generator in preset mode.
Press the HOLD button.
The "HOLD" indicator lights on the display to indicate
the preset mode. The first digit of the counter display
blinks.
3.
Set the value of the blinking digit.
Press the ADVANCE button.
The value of the blinking digit changes.
4.
Change the blinking digit.
Press the SHIFT button.
The blinking digit changes.
5.
Set the desired value for all digits.
Repeat steps
3.
and
4.
for each digit.
6.
Preset the set data in the memory.
Press the PRESET button.
The set data is saved as the time code generator value.
Following the above operation, the "HOLD" indicator
disappears from the display, the counter stops blinking
and the time code is preset.
If the REC/FREE switch is set to FREE, the time code
starts to run.
If you preset a wrong time code, perform steps
2
.
3
.
4
.
5.
and
6.
again.
PRESETTING USER'S BIT DATA
Display user's bit data on the counter display and perform
the same procedure as the time code presetting procedure.
The user's bit can be specified using numerals or alphabetic
letters from 0 to F for each digit.
Pressing the RESET button in the preset mode resets
the time code or user's bit data to 00 00 00 00.
If you press the HOLD button by mistake, press the HOLD
button once more to return to the previous display.
LIGHT
ON
OFF
COUNTER
CTL
TC
UB
RESET
OPERATE/WARNING
MONITOR
SELECT
E
REV FWD
FBATT
H
HM
MSF
REMAIN
AUD LOCK
32k
CH 1
CH 2
48k
PB NDF
AUTO OFF DEW
L iRFSERVO
HOLD
SP
MENU
OVER
OVER
40 30 20 10 0
dB
RESET button
Note:
Do not set “F” to all user's bit, or the data can not be read.
Note:
Time code presetting is not possible in the SAVE mode.
57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JVC GY-DV500 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info