Bedienungsanleitung JVC hr j 248 (Seite 15 von 48) (Englisch)

135655

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

EN 15

Repeat Playback

Your video recorder can automatically play back the whole tape

20 times repeatedly.

START PLAYBACK

Press PLAY.

ACTIVATE REPEAT

PLAYBACK

Press PLAY and hold for over 5 seconds, then release.

● The Play indicator ($) on the display panel blinks

slowly.

● The tape plays 20 times automatically, and then

stops.

STOP PLAYBACK

Press STOP at any time to stop playback.

NOTE:

Pressing PLAY, REW, FF or PAUSE also stops Repeat Playback.

Information On Colour

System

You can also record SECAM signals, or play back a MESECAM

tape on this recorder. When a MESECAM tape is played back,

"MESECAM" appears on the screen for about 5 seconds.

MESECAM is the designation for tapes with SECAM signals that

have been recorded on a MESECAM-compatible PAL video

recorder.

Index Search

Your recorder automatically marks

index codes at the beginning of

each recording. This function gives

you quick access to any one of 9

index codes in either direction.

NOTE:

Before starting, make sure the

recorder is in the Stop mode.

ACTIVATE INDEX SEARCH

Press PUSH JOG or (™ or £) on the remote

control or INDEX ™ or £ on the recorder. “™

1” or “£ 1” is displayed on screen and search begins

in the corresponding direction.

● To access index codes 2 through 9, press PUSH JOG

or or INDEX ™ or £ repeatedly until the

correct index number is displayed.

Ex.: To locate the beginning of B from the current

position, press PUSH JOG or INDEX ™ twice.

To locate the beginning of D from the current

position, press PUSH JOG or INDEX £ once.

● When the specified index code is located, playback

begins automatically.

ﬁ

£ 2

Tape Position Indicator

The tape position indicator

appears on screen when, from

the Stop mode, you press FF,

REW or perform an Index

Search. The position of “5” in

relation to “0” (beginning) or

“+” (end) shows you where you

are on the tape.

”O.S.D.” (੬ pg. 20) must be

set to “ON”, or the indicator

will not appear.

NOTE:

Depending on the type of tape used, there may be times when

the indication is not correct.

1:23:45

REMAIN 2:35

+++

Beginning End

Instant ReView

Simply by pressing a single button, the recorder power comes

on, rewinds, and begins playback of the last timer-recorded

programme. If you have several programmes recorded, you can

easily access any of them.

NOTE:

Before starting, make sure that the recorder is off and that the

Timer mode is disengaged.

ACTIVATE INSTANT

REVIEW

Press REVIEW. The recorder power comes on and the

recorder searches for the index code indicating the start

of the last timer-recorded programme. Once it’s found,

playback begins automatically.

The front display panel tells you how many programmes

have been recorded. If you have, for example, 3

programmes, “REVIEW” and "3" appear and blink. To

watch the first of the 3 programmes, press REVIEW three

times. The recorder searches and begins playback

automatically. You can access a programme as far as 9

index codes away from the current tape position.

NOTE:

Instant ReView is not possible while the recorder is in the Timer

mode.

ﬁ

Current position

AB C D E F

–2 –1 1 2 3

Index number

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC hr j 248 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info