Bedienungsanleitung JVC hr j 258 (Seite 13 von 40) (Englisch)

136057

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

EN 13

Index Search

Your recorder automatically marks

index codes at the beginning of

each recording. This function gives

you quick access to any one of 9

index codes in either direction.

NOTE:

Before starting, make sure the

recorder is in the Stop mode.

ACTIVATE INDEX SEARCH

Press PUSH JOG or on the remote control. “™

1” or “£ 1” is displayed on screen and search begins

in the corresponding direction.

● To access index codes 2 through 9, press PUSH JOG

or repeatedly until the correct index number is

displayed.

Ex.: To locate the beginning of B from the current

position, press PUSH JOG twice.

To locate the beginning of D from the current

position, press PUSH JOG once.

● When the specified index code is located, playback

begins automatically.

ﬁ

Current position

AB C D E F

–2 –1 1 2 3

Index number

Next Function Memory

You can set your recorder's power to go off automatically after

the tape is fully rewound. Before starting, make sure the

recorder is in the Stop mode.

For Automatic Power Off After Tape Rewind . . .

. . . press REW, then press within 2 seconds.

Instant ReView

Simply by pressing a single button, the recorder power comes

on, rewinds, and begins playback of the last timer-recorded

programme. If you have several programmes recorded, you can

easily access any of them.

NOTE:

Before starting, make sure that the recorder is off and that the

Timer mode is disengaged.

ACTIVATE INSTANT

REVIEW

Press REVIEW. The recorder power comes on and the

recorder searches for the index code indicating the start

of the last timer-recorded programme. Once it’s found,

playback begins automatically.

● The front display panel tells you how many

programmes have been recorded. If you have, for

example, 3 programmes, “REVIEW” and "3" appear

and blink. To watch the first of the 3 programmes,

press REVIEW three times. The recorder searches and

begins playback automatically. You can access a

programme as far as 9 index codes away from the

current tape position.

NOTE:

Instant ReView is not possible while the recorder is in the Timer

mode.

£ 2

Tape Position Indicator

The tape position indicator

appears on screen when, from

the Stop mode, you press FF,

REW or perform an Index

Search. The position of “5” in

relation to “0” (beginning) or

“+” (end) shows you where you

are on the tape.

”O.S.D.” (੬ pg. 8) must be

set to “ON”, or the indicator

will not appear.

NOTE:

Depending on the type of tape used, there may be times when

the indication is not correct.

1:23:45

+++

Beginning

End

SKIP OVER UNWANTED

SECTIONS

Press 30 SEC 1 to 4 times during playback. Each press

initiates a 30-second period of fast-motion playback.

Normal playback resumes automatically.

NOTE:

To return to normal playback during a Skip Search, press PLAY.

Skip Search

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC hr j 258 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info