Bedienungsanleitung JVC hr j 258 (Seite 32 von 40) (Englisch)

136057

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

32 EN

TROUBLESHOOTING

Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily

corrected, and this can save you the trouble of sending your video recorder off for repair.

POSSIBLE CAUSE

● The mains power cord is discon-

nected.

● “‰“ is displayed on the display

panel with Auto Timer set to "OFF".

● The batteries are discharged.

● The remote control is set to the

wrong operating mode.

SYMPTOM

1. No power is applied to the

recorder.

2. The clock is functioning properly,

but the recorder cannot be

powered.

3. The remote control won’t function.

CORRECTIVE ACTION

Connect the mains power cord.

Press the TIMER button to turn the

“‰“ indicator off.

Replace the dead batteries with new ones.

Press the appropriate button (TV or

VCR) depending on the unit you want

to operate. (੬ pg. 30)

SYMPTOM

1. The tape does not run during

recording.

2. The tape will not rewind or fast-

forward.

CORRECTIVE ACTION

Press PLAY to turn the “ “ indicator

off.

Check the cassette.

SYMPTOM

1. The playback picture does not

appear while the tape is running.

2. Noise appears during visual

search.

3. Noise appears during normal

playback.

4. Noise appears during slow-motion

playback.

5. Noise appears during still

playback.

6. The playback picture is blurred or

interrupted while TV broadcasts

are clear.

7. Playback picture has a loss of

colour.

8. No sound accompanies the

playback picture.

POSSIBLE CAUSE

● If you’re using the RF OUT connec-

tion . . .

. . . the TV receiver’s channel selector

is not set to the VIDEO channel.

. . . the recorder's VIDEO channel

has not been correctly set.

● If you’re using the AV connection, the

TV receiver is not set to the AV mode.

● This is normal.

● The automatic tracking mode is

engaged.

● The automatic tracking mode is

engaged.

● The video heads may be dirty.

● The wrong colour system is selected

for the tape being played back.

● The wrong colour system was

selected during recording.

● The TV system you have selected at

the TV System Select screen is

incorrect.

CORRECTIVE ACTION

If you are using the RF OUT connec-

tion . . .

. . . set the TV receiver to the VIDEO

channel. (

੬ pg. 4)

. . . Perform "Video Channel Set"

(੬ pg. 4)

If you are using the AV connection,

set the TV to its AV mode.

Try manual tracking. (੬ pg. 12)

Press TV PROG + or – a few times to

remove the noise bars from the screen.

Consult your JVC dealer.

Select the correct colour system by

pressing the COLOUR SYSTEM

button. (੬ pg. 24)

Once recorded, the signal cannot be

corrected. Be sure to choose the

correct setting before recording.

Set it to the correct position for the TV

broadcast system used in your area.

(੬ pg. 29.)

POSSIBLE CAUSE

● “ “ is displayed on the display

panel.

● The tape is already fully rewound or

fast-forwarded.

POWER

TAPE TRANSPORT

PLAYBACK

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC hr j 258 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info