Bedienungsanleitung JVC HR-J270 (Seite 7 von 56) (Englisch)

584566

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

PRESET DOWNLOAD

SET THE TUNER CHANNELS BY DOWNLOADING FROM YOUR TV, CLOCK AND GUIDE PROGRAM

NUMBERS

Before performing the following procedure, make sure that:

n the TV aerial cable is connected to the recorder and a 21-pin

SCART cable is connected between your TV and the recorder.

n the mains power cord is plugged into the mains outlet.

n batteries have been installed in the remote control.

Press to turn off the recorder. Press

and hold down STOP on the recorder

until the display panel shows the display

as illustrated on the right. Press PR – until

the display panel shows "_OUT– –" to set

the Video Channel to off.

Press . If "Auto" appears on the display

panel, Press

ﬁ

to select "CH – –" and

press OK or

. Preset position on the

display panel increases from "CH1";

do NOT press any button on the recorder

or remote control until the display panel

shows either the display as illustrated on

page 8 or "– – :– –".

● If "– –:– –" appears on the display panel, refer

to page 8.

● If you are using the on-screen display, the T-V

LINK screen will appear. Then the GUIDE

PROG SET screen will appear during Guide

Program number set.

● If you press any button on the recorder or

remote control while downloading is in

progress, this process will be interrupted and

you will need to start again. See NOTES below.

When you connect the recorder and your TV via fully-wired 21-pin SCART cable (Z pg. 5), you can set the recorder's tuner channels

by downloading preset data from your TV instead of using the Auto Set Up function (Z pg. 6). After downloading is completed, the

recorder sets the clock and VIDEO Plus+ assigned Guide Program numbers automatically.

For details, refer to the instruction manual for your TV.

NOTES:

●

In areas where no TV station transmits the PDC signal, the recorder cannot perform either auto clock set or auto Guide Program

number set.

●

If there is a power cut, or if you press or MENU while downloading or set up is in progress, it will be interrupted; be sure to

turn off the recorder power once and try again from the beginning.

●

Auto clock may not function properly depending on reception conditions.

●

When you perform Preset Download, be sure to use fully-wired 21-pin SCART cable.

●

On this recorder, the characters available for station names (ID) are A–Z, 0–9, –,

, + and (space). The names of some

downloaded stations may differ from those on your TV (

pg. 46).

ATTENTION

You can use this function only with a TV offering T-V Link, etc.*

* Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-wired 21-pin

SCART cable. The degree of compatibility and available functions may differ by system.

T-V LINK

PLEASE WAIT

[MENU] : EXIT

GUIDE PROG SET

PLEASE WAIT

[MENU] : EXIT

Press OK to exit Video Channel Set mode.

To view picture signals from the video recorder, set your TV to its AV mode.

— Refer to the instructions supplied with your TV set for how to do this.

– –:– –

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC HR-J270 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info