Bedienungsanleitung JVC HR-J281MS (Seite 10 von 16) (Englisch)

476523

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Page 10 September 3, 2001 9:09 am

Ⅵ B.E.S.T. — ON / OFF

When B.E.S.T. (Biconditional Equalized Signal Tracking) system is

set to “ON”, this recorder checks the condition of the tape in use

during playback and recording, and compensates to provide the

highest-possible pictures. This takes place whenever you play

back a tape or start recording after inserting a tape.

NOTE:

The recorder checks the tape condition for about 7 seconds, then

starts recording. To make sure you record the desired scene or

program completely, perform the following steps:

A Press and hold PAUSE (9), and press REC (7). After about

7 seconds, the recorder re-enters Record Pause mode.

B Press PLAY (

) to start recording.

Ⅵ PICTURE CONTROL — AUTO(NORM) / EDIT / SOFT / SHARP

This function helps you to adjust the playback picture quality

according to your preference.

AUTO (NORM): Normally select this. Picture quality is adjusted

automatically. When “B.E.S.T.” is “OFF”, “NORM” will appear

instead of “AUTO”.

EDIT: Minimizes picture degradation during editing (recording and

playback).

SOFT: Reduces image coarseness when viewing overplayed tapes

containing much noise.

SHARP: Clearer, sharper-edged picture when viewing images with

much flat, same-coloured surfaces such as cartoons.

NOTE:

Select “EDIT” when you are editing tapes. After you finish editing

the tapes, select “AUTO”.

Ⅵ PAL/MESECAM — AUTO / PAL / MESECAM

Select the appropriate colour system for recording or playback.

AUTO: Usually set to this mode. The appropriate colour system

(PAL or MESECAM) will be selected depending on the playback or

recording signals.

If the “AUTO” mode does not work properly, select either of the

following manual modes.

PAL: To record PAL signals, or playback a PAL tape.

MESECAM: To record SECAM signals, or playback a SECAM or

MESECAM tape.

NOTES:

● SECAM signals will always be recorded as MESECAM. Select

“AUTO” or “MESECAM” when recording SECAM signals.

● When playing back a SECAM tape, select “AUTO” or

“MESECAM”. The playback picture will always be

monochrome.

Ⅵ NTSC — NTSC3.58 / NTSC4.43 / NTSC]PAL

To record NTSC signals or playback a NTSC tape, it will be

necessary to select the appropriate mode.

NTSC3.58: To record NTSC signals or playback a NTSC tape.

NTSC4.43: To record NTSC4.43 signals or playback a NTSC4.43

tape.

NTSC]PAL: To playback a NTSC tape on PAL TV.

NOTE:

● The “NTSC]PAL” mode does not work during recording. In

this mode, NTSC signals will be recorded as NTSC3.58.

● The Menu screen is distorted during playing back a NTSC tape

on PAL TV. Stop playback and access the Menu screen again.

● In the “NTSC4.43” mode, with some TVs, on-screen displays

(Program screen, etc.) may roll up or down and there may be a

loss of colour. When this happens, select the “NTSC3.58”

mode.

Ⅵ AUTO TIMER — ON / OFF

● When this function is set to “ON”:

The timer recording standby mode is automatically engaged when

the recorder is turned off. It is temporarily canceled when the

recorder is turned on. You do not have to press # to engage or

disengage the timer recording standby mode.

● When this function is set to “OFF”:

You have to press # to engage or disengage the timer recording

standby mode.

Ⅵ O.S.D. — ON / OFF

When this function is set to “ON”, various recorder status

information (on-screen display) appears on the screen.

NOTE:

When you use this recorder as the source player for editing a tape,

be sure to set this function to “OFF”; otherwise, the recorder status

information (on-screen display) will be recorded on the edited

tape.

Ⅵ AUTO SP]LP TIMER — ON / OFF

When this function is set to “ON”, the recorder automatically

switches to LP mode to allow complete recording if there is not

enough tape to record the entire program while timer-recording in

SP mode.

For Example, Recording a PAL-broadcast programme of 210

minutes in length onto a 180-minute tape.

NOTES:

● If you have programed the recorder to timer-record 2 or more

programs, do not use this function, but change the tape speed

manually during timer programing.

● There may be some noise and sound disturbance where the tape

speed switches from SP to LP mode on the tape.

● The Auto SP]LP Timer feature is not available during ITR

(Instant Timer Recording), and the feature will not work

properly with any tapes longer than E-180 or with some tapes of

shorter lengths.

Approximately 150 minutes Approximately 60 minutes

SP mode LP mode

Total 210 minutes

– Other Functions –

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC HR-J281MS Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info