Bedienungsanleitung JVC HR-S7500U (Seite 65 von 76) (Englisch)

658627

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

EN 65

TROUBLESHOOTING

Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily

corrected, and this can save you the trouble of sending your VCR off for repair.

POSSIBLE CAUSE

● The power cord is disconnected.

● The TIMER mode is engaged with

Auto Timer set to "OFF" (Z pg. 52).

● The Child Lock mode is engaged.

● The batteries are discharged.

SYMPTOM

1. The power won’t come on.

2. The clock works, but the VCR’s

power won’t come on.

3. The remote control won’t function.

CORRECTIVE ACTION

Connect the power cord.

Press TIMER to disengage.

Press and hold POWER on the remote

to disengage the mode (Z pg. 64).

Replace the dead batteries with new

ones.

SYMPTOM

1. The cassette gets stuck partway

during loading, and is ejected.

CORRECTIVE ACTION

Make sure the cassette's window is

facing up, the rear label side is facing

you and the arrow on the front of the

cassette is pointing towards the VCR.

Then insert the cassette.

POSSIBLE CAUSE

● The cassette was inserted incorrectly.

SYMPTOM

1. The tape is running but the picture

won’t appear.

2. Breaks are noticeable in Hi-Fi

soundtrack.

3. The playback picture is blurred or

interrupted, even though TV

broadcasts are clear.

4. The Hi-Fi soundtrack cannot be

heard.

POSSIBLE CAUSE

● If you’re using the RF OUT connec-

tion (Z pg. 6), the channel selector

on the TV is set incorrectly.

● If you’re using the AV connection

(Z pg. 6), the TV receiver is set to

the wrong mode.

● Automatic tracking is engaged.

● The video heads may be dirty.

● The AUDIO MONITOR option was

set incorrectly.

CORRECTIVE ACTION

Set the channel selector to channel 3

or 4.

Set the TV receiver to its AV mode.

Disengage Auto Tracking and adjust

the tracking manually (Z pg. 25).

The heads must be cleaned. Consult

your JVC dealer.

Set AUDIO MONITOR to "HI-FI"

(Z pg. 29).

CORRECTIVE ACTION

Insert a cassette.

Remove the cassette and cover the

hole with adhesive tape, or load a

cassette on which the record safety

tab is intact.

Set the VCR to the appropriate

channel.

Refer to the directions and the

illustration under “Edit To Or From

Another VCR” (Z pg. 55) or “Edit

From A Camcorder” (Z pg. 56) and

properly connect the units.

Make sure the power to all units is on.

Select the recorder’s appropriate

input mode.

POSSIBLE CAUSE

● There’s no cassette loaded.

● The loaded cassette has had its

record safety tab removed.

● The VCR has been set to its AUX

mode by mistake.

● The VCRs or the camcorder and the

VCR have been incorrectly con-

nected.

● The power to one or more of the

units has not been turned on.

● The recorder’s input mode has been

set incorrectly.

SYMPTOM

1. Recording won’t start.

2. TV broadcasts won’t record

properly.

3. Tape-to-tape editing won’t work.

POWER

TAPE TRANSPORT

PLAYBACK

RECORDING

CONTINUED ON NEXT PAGE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC HR-S7500U Seite 65

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info