Bedienungsanleitung JVC HR-S9400U (Seite 48 von 76) (Englisch)

658628

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

48 EN

TIMER RECORDING (cont.)

You can directly program the VCR’s timer to record up to 8

shows, as far as a year in advance. Remember, the clock must be

set before you can program the timer (Z pg. 8 or 9).

You can also use the optional Illumi-Guide feature, where the

relevant buttons on the remote control light to tell you which

button to press next. The Illumi-Guide feature is activated by the

ILLUMI GUIDE button on the remote control. The Illumi-Guide

feature is only active when the remote control's TV/CABLE/VCR

switch is set to "VCR". (Illumi-Guide is an optional help feature

which makes programming easier. It is not necessary to use

Illumi-Guide to program the VCR.)

On-Screen

Timer

Programming

NUMBER

When Using The Illumi-Guide Feature

● Buttons light or blink on the remote control for

approximately 10 seconds. If the button or buttons extinguish

during timer programming, press ILLUMI GUIDE and the

button or buttons previously lit or blinking come back on. If

the button or buttons do not re-light or start blinking again,

press MENU as many times as necessary to return to the

normal screen and extinguish all illuminated buttons,

and re-perform the timer programming procedure from the

beginning.

● If for some reason the remote control's signal is not received

by the VCR, press MENU as many times as necessary to

return to the normal screen and extinguish all

illuminated buttons, and re-perform the timer programming

procedure from the beginning.

LOAD A CASSETTE

Make sure the record safety tab is intact. If not, cover

the hole with adhesive tape, then load.

● The VCR comes on, and the counter is reset,

automatically.

ACCESS ON-SCREEN

To use the Illumi-Guide feature press ILLUMI GUIDE.

The MENU, REW, PLAY and FF buttons will light.

Press MENU as many times as necessary to bring up the

Main Menu screen.

● If you are using the Illumi-Guide feature, MENU

lights up and OK blinks.

ACCESS PROGRAM SET

SCREEN

Make sure the arrow is to the left of "PROGRAM SET",

then press OK.

● If you are using the Illumi-Guide feature, OK blinks

when the following buttons are lit: NUMBER keys (0

– 9), TIME SCAN, CANCEL and MENU.

SELECT PROGRAM NUMBER

Press the appropriate

NUMBER keys or CH5

∞

TIME SCAN 5

∞

to select a

vacant program number,

then press OK. The first time

you set the timer program-

ming function, all the

program numbers will be

blank; in this case just press

OK when the Program Set screen appears.

● If you are using the Illumi-Guide feature, OK blinks

when the following buttons are lit: NUMBER keys

(0 – 9), TIME SCAN, CANCEL and MENU.

PROGRAM 1

DATE - - / - -

START - - : - - AM

STOP - - : - - AM

CHANNEL - - SP

PRESS NUMBER KEY(0-9)

OR (

,∞), THEN (OK)

PRESS (MENU) TO END

ILLUMI GUIDE

TIME SCAN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC HR-S9400U Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info