Bedienungsanleitung JVC HR-S9900U (Seite 74 von 88) (Englisch)

658631

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

74 EN

TROUBLESHOOTING

Before requesting service, use this chart and see if you can repair the trouble yourself. Small problems are often easily

corrected, and this can save you from the trouble of sending your VCR off for repair.

POSSIBLE CAUSE

● The AC power cord is disconnected.

● The VCR is in the timer recording

standby mode with “AUTO TIMER”

set to “OFF” (墌 pg. 57).

● The child lock function is activated.

● The batteries are discharged.

SYMPTOM

1. The power will not come on.

2. The clock works, but the VCR’s

power will not come on.

3. The Remote will not function.

CORRECTIVE ACTION

Connect the AC power cord.

Press TIMER to disengage.

Press and hold POWER on the

Remote for more than seven seconds

to release the child lock function (墌

pg. 62).

Replace the dead batteries with new

ones.

SYMPTOM

1. The cassette gets stuck partway

during loading, and is ejected.

CORRECTIVE ACTION

Make sure the cassette’s window is

facing up, the rear label side is facing

you and the arrow on the front of the

cassette is pointing towards the VCR.

Then insert the cassette.

POSSIBLE CAUSE

● The cassette was inserted incorrectly.

SYMPTOM

1. The tape is running but the picture

will not appear.

2. Breaks are noticeable in Hi-Fi

sound track.

3. The playback picture is blurred or

interrupted, even though TV

broadcasts are clear.

4. The Hi-Fi sound cannot be heard.

POSSIBLE CAUSE

● If the RF connection (墌 pg. 7) is

used to view the picture, the

channel on the TV is set incorrectly.

● If the AV connection (墌 pg. 7) is

used to view the picture, the TV

receiver is set to the wrong mode.

● Automatic tracking is engaged.

● The video heads may be dirty.

● Audio Monitor setting is incorrect.

CORRECTIVE ACTION

Select channel 3 or 4 on the TV.

Select the AV mode on the TV.

Disengage auto tracking and adjust

the tracking manually (墌 pg. 25).

The heads must be cleaned. Consult

your JVC dealer.

Set Audio Monitor to “HI-FI”

(墌 pg. 25 or 59).

CORRECTIVE ACTION

Insert a cassette.

Remove the cassette and cover the

hole with adhesive tape, or load a

cassette on which the record safety

tab is intact.

Select the appropriate channel on the

VCR.

Connect the components correctly

(墌 pg. 64 – 69) or check “REAR AUX

INPUT” and “FRONT AUX INPUT”

setting (墌 pg. 60).

Make sure the power to all units is on.

Select the appropriate input mode on

the recording VCR.

POSSIBLE CAUSE

● There is no cassette loaded.

● The loaded cassette has had its

record safety tab removed.

● The VCR has been set to “L-1” or “F-

1” input mode by mistake.

● The components have been

incorrectly connected, or correct

video connector (S VIDEO or

VIDEO) is not selected.

● The power to one or more of the

units has not been turned on.

● The recording VCR’s input mode has

been set incorrectly.

SYMPTOM

1. Recording will not start.

2. TV broadcasts will not be recorded

properly.

3. Tape-to-tape editing will not work.

POWER

TAPE TRANSPORT

PLAYBACK

RECORDING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JVC HR-S9900U Seite 74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info