Bedienungsanleitung JVC hr-v610 (Seite 10 von 16) (Englisch)

134631

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Page 10 June 7, 2004 1:31 pm

—10—

Other Functions

Checking tape position

When you change the recorder operation

mode from the stop mode to fast forward

or rewind mode, or when you perform an

Index Search or Instant Review, the tape

position indicator appears.

The position of “

q” in relation to “0”

(beginning) or “+” (end) shows you where

you are on the tape.

● Set “O.S.D.” to “ON” (

 10).

Changing display information

Each time you press ––:––, the display panel shows

the channel number and the clock time alternatively.

● You can change display in the stop, recording or

during rewind/fast-forward.

● When “O.S.D.” is set to “ON” (

 10) and ––:––

on the remote control is pressed, time counter will

appear on the TV screen. To reset the time counter, press 0000

on the remote control.

Function settings

You can use the other useful function settings on the Function Set

screen.

A Access Main Menu screen, then

Function Set screen

Press MENU on the remote control. Press

rt to place the pointer next to

“FUNCTION SET”, then press OK or

B Select Function

Press rt to place the pointer next to the

function you want to set.

C Change setting

Press OK or e. The default setting is bold in the following table.

Press MENU to return to normal screen.

 B.E.S.T. — ON / OFF

When B.E.S.T. (Biconditional Equalized Signal Tracking) system is

set to “ON”, this recorder checks the condition of the tape in use

during playback and recording, and compensates to provide the

highest-possible pictures. This takes place whenever you play

back a tape or start recording after inserting a tape.

NOTES:

● The recorder checks the tape condition for about 7 seconds,

then starts recording. To make sure you record the desired scene

or program completely, perform the following steps:

A Press and hold 9, and press 7. After about 7 seconds, the

recorder re-enters Record Pause mode.

B Press 4 to start recording.

● B.E.S.T. does not work when the satellite auto recording mode is

engaged (

 11).

 PICTURE CONTROL — AUTO(NORM) / EDIT / SOFT

This function helps you to adjust the playback picture quality

according to your preference.

AUTO (NORM): Normally select this. Picture quality is adjusted

automatically. When “B.E.S.T.” is “OFF”, “NORM” will appear

instead of “AUTO”.

EDIT: Minimizes picture degradation during editing (recording and

playback).

SOFT: Reduces image coarseness when viewing overplayed tapes

containing much noise.

NOTE:

Select “EDIT” when you are editing tapes. After you finish editing

the tapes, select “AUTO”.

 PAL/MESECAM — AUTO / PAL / MESECAM

Select the appropriate colour system for recording or playback.

AUTO: Usually set to this mode. The appropriate colour system

(PAL or MESECAM) will be selected depending on the playback or

recording signals.

If the “AUTO” mode does not work properly, select either of the

following manual modes.

PAL: To record PAL signals, or playback a PAL tape.

MESECAM: To record SECAM signals, or playback a SECAM or

MESECAM tape.

NOTES:

● SECAM signals will always be recorded as MESECAM. Select

“AUTO” or “MESECAM” when recording SECAM signals.

● When playing back a SECAM tape, select “AUTO” or

“MESECAM”. The playback picture will always be

monochrome.

 NTSC — NTSC3.58 / NTSC4.43 / NTSC]PAL

To record NTSC signals or playback a NTSC tape, it will be

necessary to select the appropriate mode.

NTSC3.58: To record NTSC signals or playback a NTSC tape.

NTSC4.43: To record NTSC4.43 signals or playback a NTSC4.43

tape.

NTSC]PAL: To playback a NTSC tape on PAL TV.

NOTES:

● The “NTSC]PAL” mode does not work during recording. In this

mode, NTSC signals will be recorded as NTSC3.58.

● The Menu screen is distorted during playing back a NTSC tape

on PAL TV. Stop playback and access the Menu screen again.

● In the “NTSC4.43” mode, with some TVs, on-screen displays

(Program screen, etc.) may roll up or down and there may be a

loss of colour. When this happens, select the “NTSC3.58”

mode.

 AUTO TIMER — ON / OFF

● When this function is set to “ON”:

The timer recording standby mode is automatically engaged when

the recorder is turned off. It is temporarily canceled when the

recorder is turned on. You do not have to press # to engage or

disengage the timer recording standby mode.

● When this function is set to “OFF”:

You have to press # to engage or disengage the timer recording

standby mode.

 O.S.D. — ON / OFF

When this function is set to “ON”, various recorder status

information (on-screen display) appears on the screen.

NOTE:

When you use this recorder as the source player for editing a tape,

be sure to set this function to “OFF”; otherwise, the recorder status

information (on-screen display) will be recorded on the edited

tape.

Turn on the recorder and the TV, and set your TV to its AV mode

or video channel

+++ +

1 : 23 : 45

REMAIN 1 : 49

[ / ]

[MENU] : EXIT

MAIN MENU

FUNCTION SET

TUNER SET

INITIAL SET

[ / ]

[MENU] : EXIT

FUNCTION

B.E.S.T. ON

PICTURE CONTROL AUTO

PAL/MESECAM AUTO

NTSC NTSC3.58

AUTO TIMER OFF

O.S.D. ON

AUTO SP LP TIMER OFF

HR-V610AA.AG.AJ_EN_B.fm Page 10 Monday, June 7, 2004 1:31 PM

Downloaded from www.Manualslib.com manuals search engine

JVC hr-v610 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JVC hr-v610

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info